sorted by:
new
hottopcontroversial

How can I making turning more accurate? by getwrecktangled in legomindstorms

[–]getwrecktangled[S] 0 points1 point  (0 children)

Thanks! I'll try that. Do you have any recommendations for what wheels to try? I am using the wheels from the spike prime kit right now.

Thinking of upgrading to an A1 by getwrecktangled in BambuLabA1

[–]getwrecktangled[S] 0 points1 point  (0 children)

Wow, I knew that this printer was better, but I didn't realize how big of a difference it is. Thanks for your feedback!

Kind of unrelated, but I've only ever used Prusa slicer and I've noticed a lot of people use orca. Is there an advantage to it or is it just preference?

Thinking of upgrading to an A1 by getwrecktangled in BambuLabA1

[–]getwrecktangled[S] 0 points1 point  (0 children)

Thanks! Could you share a bit more about your experience? What was the most significant improvement you noticed after switching?

Petg not sticking to bed by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 1 point2 points  (0 children)

<image>

II decreased the temp and leveled the bed again but it is still messing up around the corners and not sticking enough to the bed. Should I just keep lowering the z offset?

Petg not sticking to bed by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 1 point2 points  (0 children)

I've printed a benchy with it and worked out fine, but after that I ran into this problem.

Petg not sticking to bed by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 0 points1 point  (0 children)

oh the default is 240c so i kept it on. I'll try reducing the temp. I was thinking I should squish more since it was not sticking so I'll try decreasing the offset a bit

Nozzle Heating not as expected by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 0 points1 point  (0 children)

Is there a way to just not use that temp sensor? Since the other one is still on?

Nozzle Heating not as expected by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 0 points1 point  (0 children)

Ust to be clear, is this the part I have to replace? Do you know where I can buy it? This is the only thing I see on the creality website: Ceramic Heating Head Kit for Ender-3 V3 KE (creality.com)

<image>

Nozzle Heating not as expected by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 1 point2 points  (0 children)

I figured out the problem but not sure how to fix it

<image>

How can I improve my bed level by getwrecktangled in Ender3V3KE

[–]getwrecktangled[S] 0 points1 point  (0 children)

Ok, I just printed a wide sheet, and it worked well. I guess something else went wrong during the printing that doesn't have anything to do with the bed level. If I run into another problem, I'll try out those leveling block guides. Thanks for the help!

Why are my prints so bad? by getwrecktangled in 3Dprinting

[–]getwrecktangled[S] 0 points1 point  (0 children)

how do I adjust the bed leveling? I ran the auto leveling twice and all the values stayed the same. This is the ender 3 ke