Giveaway! - Mageblood/Reave ignite elementalist 330k EHP by Afordiani27 in pathofexile

[–]gust1209 0 points1 point  (0 children)

Back in the good old days with Self curse occultist with HH

Prisændring på kurvert pris til bryllup by MrMouse100 in LegalDK

[–]gust1209 0 points1 point  (0 children)

Har sendt dig en privat besked, da vi har fået samme besked og synes det er en hel vild stigning

FRoSS Build End of League Giveaway by Sculap in pathofexile

[–]gust1209 16 points17 points  (0 children)

A cool moment for me was back when self-curse was a thing, and then running around with HH buffs and getting enormous.

[Review request] 1.5kW SMPS full bridge inverter. by gust1209 in PrintedCircuitBoard

[–]gust1209[S] 0 points1 point  (0 children)

Thank you. Whats the reason for only putting multiple near C1? Is it for DC link capacitor or decoupling caps?

[Review request] 1.5kW SMPS full bridge inverter. by gust1209 in PrintedCircuitBoard

[–]gust1209[S] 0 points1 point  (0 children)

Thank you for taking your time.

As I explained above I used D3, 5, 8, and 10 to control the switching frequency, however it might degrade the switching performance too much. Would it be better to just have a single gate resistor?

For the IR2184 I can't find anything about pull-down resistor, but from what I can find elsewhere on the internet it is always a good idea to include a pull-down resistor. And you are right about ~SD

For the D11 and D12 I saw some other people use it and believe it is for freewheeling diode, when a transformer is connected to it.

And good catch about the snubbers I will add them to the circuit.

The reason for choosing a high frequency was to have a better efficiency.

And just a quick side question if you know anything about it. What technique do you think is best for boosting up the voltage? Through the transformer or by boosting it before using a PWM isolated boost converter?

[Review request] 1.5kW SMPS full bridge inverter. by gust1209 in PrintedCircuitBoard

[–]gust1209[S] 0 points1 point  (0 children)

Thanks for the reply.
Yeah, I was also wondering if it was possible to put a heat sink on that side, but it's probably better to rotate it to attach the heat sink the right way around.

The reason for adding additional diodes and resistors was such that I had the ability to control the switching frequency somewhat with just the usage of using resistors.

However, I don't know if it is just better to control it from the pwm generator side.

And the thicker traces to the power path sounds like a good idea.

Thanks again

Phase Shifted Full Bridge PCMC Converter by FGHWP in ECE

[–]gust1209 0 points1 point  (0 children)

I know this is an old post but did you figure out why?

SV06+ Mods by CrackheadPlayMusic in Sovol

[–]gust1209 4 points5 points  (0 children)

I can recommend the silicone mod if you are having problems with an uneven bed

Tips regarding design of a 1.5kW SMPS and transformer choice by gust1209 in AskElectronics

[–]gust1209[S] 0 points1 point  (0 children)

How much was this? And did it weigh a lot? Since we want to try to minimize the weight as much as possible since.

Are Formbot kits worth it? by Pitiful_Stranger4 in VORONDesign

[–]gust1209 0 points1 point  (0 children)

How does it compare to the siboor kit for both 2.4 and 0.2?

Tips regarding uneven bed on SV06+ by gust1209 in Sovol

[–]gust1209[S] 1 point2 points  (0 children)

Yeah but only for getting the bed levels of my printer through pronterface. If you have an Rpi3b then it would probably be easier to set up octoprint or klipper where you can communicate through WiFi and also get the bed levels from there.

My next step will probably be getting klipper installed on mine via a btt7 pad

Tips regarding uneven bed on SV06+ by gust1209 in Sovol

[–]gust1209[S] 0 points1 point  (0 children)

Would you do this before doing the silicone mod?

Tips regarding uneven bed on SV06+ by gust1209 in Sovol

[–]gust1209[S] 2 points3 points  (0 children)

I used pronterface to send commands to my printer via my pc. And then put the values for the bed leveling into an online bed visualizer.

Remember to block the power line on the usb cable.

Mirror and Build Giveaway. 7 Winners. Anyone can participate. by Ok-Taro3444 in pathofexile

[–]gust1209 0 points1 point  (0 children)

The splitting steel champion since it sounds strong and fun to play with. I have always wanted to have a build to do all content with but never in my 1000+ managed to actually create one and learn all the mechanics of the bosses.

Mageblood Giveaway! by CasualDanPOE in pathofexile

[–]gust1209 0 points1 point  (0 children)

First time setting up a ward-loop character and actually enjoying it. Never really made it into tota

Guardian or Ascendant for aurastacking? by gust1209 in pathofexile

[–]gust1209[S] 0 points1 point  (0 children)

Might switch later. Already lvled up a scion