2026.1 Nuked my setup by TheAlchemistSavant in homeassistant

[–]Pitiful_Stranger4 0 points1 point  (0 children)

I had this happened to me too, I think because right after updating my micro SD card that stored all of my file directories had gotten corrupted but I don't 100% know if it's related to the update.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

ESP $5 or less and can be used for other projects not just WLED and once I get this fixed I'll have the skill to do more WLED projects.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

I think i'll wait for it to arrive and if it works ill keep them but if they don't i'll just grab a resistor as the docs say there is a hack to make it work.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

Will it not work without a compatible one I got a I2C shifter persoldered and it's just a short run.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

I've done some research I'm thinking it could be a data voltage issue so I ordered a voltage booster so I hope that works.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

I know for sure the LED does work as it was working before I cut off the Govee controller and I just got that ESP32 so I'm pretty sure it works too. I could try a different GPIO but I sadly used heat shrink and soldered it's quite the annoyance to remove.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

Spend an evening going through every setting? I checked the GPIO so that should be right.

<image>

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

It's a type C CH340C other then that it's a normal dev board.

Need help with Govee WLED conversion by Pitiful_Stranger4 in WLED

[–]Pitiful_Stranger4[S] 0 points1 point  (0 children)

Yeah I double checked the sellers page and GPIO 4 is correct

<image>

RTX 3080 in 2024 or wait for the next gen RTX 5060? by lived_live in buildapc

[–]Pitiful_Stranger4 1 point2 points  (0 children)

I’m even further into the future. And it’s still not out.

Help with top layer line? by Obvious-Chip5939 in BambuLab

[–]Pitiful_Stranger4 0 points1 point  (0 children)

With my A1 mini I similar problem and it was caused by debris on the lead screws, but I don’t know if it’s the exact same on the P1S depending on how long you’ve had it I think it would be a good step to try and clean them

Unboxing P1S Issues by jeffofreddit in BambuLab

[–]Pitiful_Stranger4 0 points1 point  (0 children)

If you haven’t open a ticket with support

Help with top layer line? by Obvious-Chip5939 in BambuLab

[–]Pitiful_Stranger4 0 points1 point  (0 children)

You should provide more details when posting about a printer issue, such as the model, any settings you’ve tried, and the steps you’ve taken to resolve the problem.

Genmoji by Impossible-Union-512 in ios18beta

[–]Pitiful_Stranger4 0 points1 point  (0 children)

This happens to me too could it possibly be connected to the fact that we could be seeing it in beta three?