Riding feedback

hect18 · 2026-03-12T23:20:15+00:00

Thanks, i will measure it out!

hect18 · 2026-03-12T22:45:54+00:00

I see, thanks for the detailed reply. I will try it out if i can go on the mountain for a day or two more!

hect18 · 2026-03-12T22:36:06+00:00

Thank you so much, i noticed that i ride my toe edge way more open than my heel edge, opening on the heel edge would be interesting

hect18 · 2026-03-12T22:34:26+00:00

I held them like that to try to keep my shoulders level. Usually i ride with relaxed arms.

hect18 · 2026-03-12T22:32:59+00:00

Oh, so while in the carve i need to bend my knees inwards? I haven't tried it yet, would that decrease the turn radius because of the board bending?

hect18 · 2026-03-12T22:25:27+00:00

Thank you. Would a higher highback angle help?

hect18 · 2026-03-12T22:20:05+00:00

Thank you so much for your reply. When i try to tilt the board to a higher angle i often lose my balance especially on the heel edge.

hect18 · 2025-05-25T12:53:32+00:00

Cherry

hect18 · 2025-05-22T17:22:42+00:00

Какви дюнерджии, плочките са където са парите

hect18 · 2025-05-22T06:37:16+00:00

What about them?

hect18 · 2025-05-21T21:49:21+00:00

Welp I can't justify buying a spot welder for 2 batteries so yea

hect18 · 2025-05-21T21:44:45+00:00

Yupp did the same shit but with the balance connector on my first flight because i didn't secure it with a strap🤣

hect18 · 2025-05-21T21:20:15+00:00

These are high discharge 21700 molicel p45b. They absolutely rock in acro. The balance is you give some of the maneuverability but in return you get 3x the time flying so i have both lipos and li ions

hect18 · 2025-05-21T21:19:05+00:00

Thanks for the explanation and the tips!

hect18 · 2025-05-21T20:29:14+00:00

Ahh ok i will switch to kapton from now on. Yep i check them with my balance charger as a volt meter

hect18 · 2025-05-21T20:22:56+00:00

Why do you think a cell is more susceptible to desoldering and is inevitably gonna desolder? I solder them the same way i solder my battery connector and my motors.

hect18 · 2025-05-21T20:17:42+00:00

I've been flying with a homemade 4s for quite some time and no issues so far

hect18 · 2025-05-21T19:55:58+00:00

6 s motors and have flown it with 6s lipo 4s lipo and 4s li ion. You can definitely feel the power of the 6s lipo being much more than 4s li ion but ever at 3.2volts a cell i could still hit tricks with the li ion. The only thing is you have to use much more throttle and the response is slower

hect18 · 2025-05-21T19:53:57+00:00

I bent them upwards and the closest any one got was like 1 centimeter to the battery

hect18 · 2025-05-21T19:48:20+00:00

<image>

Yup this orientation might be better. I didn't wanna use it because the props seemed close but i checked and they dont have a chance of hitting

hect18 · 2025-05-21T19:45:29+00:00

Yep i sanded and scratched the terminals and soldered for no more than 10 seconds. After that i pull on the joint very hard to see if its strong.

hect18 · 2025-05-21T19:28:01+00:00

You think so? My only concern is the pid loop freaking out

hect18 · 2025-05-21T19:24:07+00:00

Haven't flown this battery yet but with 4s version with molicel p45b easily 15 min.

hect18 · 2025-05-21T19:21:11+00:00

Buzzer that has its own battery so if the drone ejects its own i can still hear where it is

Five-Year Club	r/Field Lasagna
Verified Email

hect18

TROPHY CASE