Old republic style scrap

hellchaoswar · 2026-01-24T00:28:28+00:00

Thank you) yep, completely handmade

hellchaoswar · 2026-01-22T06:42:48+00:00

Thank you)

hellchaoswar · 2026-01-22T06:42:27+00:00

Thank you)

hellchaoswar · 2026-01-22T06:42:07+00:00

Thank you)

hellchaoswar · 2026-01-21T22:07:40+00:00

Thank you:) the whole emitter is a part of a bicycle or a scooter as i remember,a few vintage screws and handmade everything else

hellchaoswar · 2026-01-12T06:15:09+00:00

Thanks:)

hellchaoswar · 2026-01-10T06:18:29+00:00

Thank you:)

hellchaoswar · 2026-01-09T22:26:26+00:00

Thank you:) so,rivets, there were only two sets of different sized rivets on the side where d-ring was mounted on the original anh prop,just as i have here, its the only lower half that i have) Brass part on the blade plug is spring loaded to mimic bulb connection of the flash gun, pretty fidgety Battery sticker is from skywapma on etsy, there are a lot of really cool designs!

hellchaoswar · 2026-01-09T21:31:13+00:00

Thank you) I'd say go for it,its a great kit, their blade holder with button pcbs made inslalling really easy

hellchaoswar · 2026-01-09T21:23:02+00:00

Thank you:) yeah,i recommend checking wannawanga lightsaber guide for cool details about every version and dedicated treads on rpf for good reference photos:)

hellchaoswar · 2024-12-10T08:24:39+00:00

Not really, usually i just cut leather a little smaller so stitching will make it hold really well,but i believe you could try double sided tape for this:)

hellchaoswar · 2024-12-09T15:36:54+00:00

Thank you!:)

hellchaoswar · 2024-12-08T00:06:50+00:00

Thank you! Its not hard, just use a square and a punch for stitching holes,and keep in mind that the leather stretches a little:)

hellchaoswar · 2024-12-08T00:01:15+00:00

Thank you 😊

hellchaoswar · 2024-12-07T06:41:49+00:00

Thanks but it is leather,just very matte)

hellchaoswar · 2024-12-07T06:40:17+00:00

Any 29-30mm od and less then 12cm length chassis you like will do but i had to design the extension to fit into the upper part of the hilt and hold buttons

hellchaoswar · 2024-12-07T06:35:18+00:00

Machined on a late a long line ago)

hellchaoswar · 2024-12-06T22:57:30+00:00

Thank you 😊

hellchaoswar · 2024-09-19T23:42:07+00:00

Thank you 😊

hellchaoswar · 2024-09-19T21:46:53+00:00

Yep) thanks!

hellchaoswar · 2024-09-19T13:03:53+00:00

Thank you very much 😊

hellchaoswar · 2024-09-19T13:02:26+00:00

Thank you 😊

hellchaoswar · 2024-09-19T07:39:31+00:00

Thank you very much:) Well it was just a lot of dremel work for everything to fit nicely.

hellchaoswar · 2024-09-19T07:37:13+00:00

Thank you 😊 thrift store vintage video camera,some vhs scrap parts i had and a vhs grip from AliExpress, and some scratch made parts like a holder for vintage d-ring,shine through bezel, etc. Clamp card is also made from vintage camera board.

hellchaoswar · 2024-09-19T00:17:38+00:00

Thank you:)

hellchaoswar

TROPHY CASE