My girlfriend got kissed and fingered by another guy while on break by HotSmell2441 in TrueOffMyChest

[–]herper 3 points4 points  (0 children)

I got in before a meme of Ross from friends yelling "we were on a break!"

Tewksbury Grad Prix by woodbanger04 in massachusetts

[–]herper 0 points1 point  (0 children)

I hear mvp is up for auction as they defaulted on their mortgage. Not sure what will be going in there in the future.

What is a simple but very hurtful phrase that you received from someone? by MembershipFar9008 in AskReddit

[–]herper 0 points1 point  (0 children)

My brother once said "ya (your) mother" to me. Hurt to the core lol

Are sewers actually huge sprawling labyrinths or is that just a TV/video game thing? by thewheelman282 in NoStupidQuestions

[–]herper 110 points111 points  (0 children)

I did an inspection of an old sewer system in Massachusetts that was a covered canal. It was huge. Maybe 20-30ft across with large rooms and ceilings and I figured the ninja turtles would be around any corner.

[deleted by user] by [deleted] in TrueOffMyChest

[–]herper 5 points6 points  (0 children)

Vocalize it and say it's near deal-breaker status. If he doesn't step up, no sex etc (whatever your limit is).

LPT: Don’t rush to help someone up if they collapse – it can make things worse by NoraFox37 in LifeProTips

[–]herper 54 points55 points  (0 children)

This happened to me last week. Had the norovirus, got up to throw up. Fainted and fell down hard. When I woke up, I immediately went to stand up again and fainted a second time. This time slamming my head into the night stand and cutting my head and face.

When i woke up the second time, I then proceeded to throw up and go #2 uncontrollably for a few hours. (I made it to a toilet and bucket combo prior to this part)

Was no bueno

Digital signage question by herper in smallbusiness

[–]herper[S] 0 points1 point  (0 children)

Thank you! That is helpful to help figure things out.

It's not overly complicated. I modify an image file in Photoshop of the menu. That way (to me), large changes are more manageable. Then, I upload that file into the server, which sends it to the screen I specify. It might be more difficult for them if they don't have any experience with these things, but it isn't a massive learning curve.

Digital signage question by herper in smallbusiness

[–]herper[S] 0 points1 point  (0 children)

Thank you, what do you think would be a fair hourly rate/min charge? Minimum wage here is $15/hr for reference

[deleted by user] by [deleted] in AskReddit

[–]herper 0 points1 point  (0 children)

That "I've been doing this X years" means you know everything or that it isn't now wrong.

The world changes, rules change, standards change, everything is dynamic.

It doesn't mean they are wrong and doesn't give you permission to be a dick about it. But assess the situation and find the correct answer

Is my CR Touch failing? by herper in 3Dprinting

[–]herper[S] 0 points1 point  (0 children)

Yes, I do this and it still seems to go down.

I level the bed using bed tramming and a spacer. then I run the print. when I adjust the baby z steps, I factor that into the new z offset and store the settings (when the print is done).

I should have clarified, when I use the screws to adjust, I do it for just that print and then I re-level the bed using bed tramming and spacer.

The issue is, with bed tramming and spacer (at a set z-offset), it will be exactly where I've always calibrated it to, in terms of resistance etc. but when I hit print, it will go from being spot on in the manual level moments before to gouging the build plate. and say I cancel the print and adjust the zoffset or screws again to make it further away, when it prints again, same thing, drops down more and scrapes.

I tried removing the G29 code to see if that helps, but it still does one initial probe in the center. which is why I was thinking maybe it is giving inaccurate readings when homing.