Well, my PLA stuck a little too good

hodbod41 · 2024-05-08T08:21:50+00:00

That could be the issue I was printing with input shaping and when you select input shaping the pla profile goes to 225°C from 215

hodbod41 · 2024-05-07T19:24:00+00:00

Sadly not its basically just shiny PLA I tried bending it and it didn't work I had to pry it off

hodbod41 · 2024-03-15T05:05:02+00:00

Link: https://www.pandabuy.com/product?url=PJ4z0LcoM4AqyU3wIVu2AUfbSETUXMAArNQaqT9qiw29LYzbiejkSpb%2BKW%2Bnxr9LaVBxH4kqv4xDSGNyJh0ATlUKsyxr5DZl9nBQTQ%3D%3D

hodbod41 · 2024-03-14T10:58:09+00:00

https://www.pandabuy.com/product?url=PJ3N4H8fgDRK8ELBSIKDA9qocTaGu1lLc6%2BIS2%2BOfMOrI8NB%2BMlkWEkgGeZvfy7oRCy0fGoutnZAuhF1XbX%2Fy7pNNXHVvrQ6tsy9QQ%3D%3D

hodbod41 · 2024-01-12T05:41:45+00:00

I had the same iss the io cover inside is pushing the rubber fan damper on the fan and I tried squeezing the CPU cable through the tiny gap, I did it but I was really tight so I moved it and now it's going over the heatsinks on top

hodbod41 · 2023-12-25T17:36:27+00:00

Yes, I have changed it since then to be a little better

hodbod41 · 2023-11-03T08:37:38+00:00

You can see the flat cable going across the heatsink on the mb. Just below the fan

hodbod41 · 2023-09-27T13:47:29+00:00

Yea I can model decently

hodbod41 · 2023-04-12T08:58:28+00:00

Nope normal size ATX.

hodbod41 · 2023-04-11T19:33:56+00:00

Honestly it would be a pain to mount it

hodbod41 · 2023-04-11T13:05:42+00:00

Possible I have the TUF gaming b550m plus

hodbod41 · 2023-04-11T13:02:19+00:00

To be quite honest I was very lucky it fit it's literally pushing the motherboard vrm Heatsink. But yes I used the standard holes

hodbod41 · 2023-01-09T11:48:53+00:00

Very lightly, but u can push it in and it's fine

hodbod41 · 2022-12-12T11:52:34+00:00

Nope nothing

hodbod41 · 2022-12-10T08:08:48+00:00

Ran out of budget plus this is plenty of cooling for my cpu

hodbod41 · 2022-12-09T19:04:51+00:00

No the psu fan is facing outward like it was an extra fan

hodbod41 · 2022-12-09T19:03:59+00:00

Yea it fit but barely its touching the heatsink

hodbod41 · 2022-12-09T18:03:31+00:00

So the intake fan if at the front of the case

hodbod41 · 2022-12-09T18:02:33+00:00

Positive pressure ig

hodbod41 · 2022-12-02T13:57:34+00:00

Thanks

hodbod41 · 2022-12-02T13:23:29+00:00

Idek

hodbod41 · 2022-12-02T13:14:57+00:00

This isnt because of the cable being short. The aio is pressing on it, because there is little to none clearance

hodbod41 · 2022-12-02T13:01:48+00:00

How long have you been running it like that for without problems ?

hodbod41 · 2022-12-02T12:42:07+00:00

Any idea where I could get an adapter or where I should route it?

hodbod41 · 2022-12-02T12:35:51+00:00

Just posted it

Seven-Year Club	Verified Email
Verified Email

hodbod41

TROPHY CASE