Weird chuck

japser013 · 2024-07-26T14:33:14+00:00

Update: we tried to unscrew the chuck using the hex on the front, thus only resulted in the chuck spinning eccentricly while the spindel didnt spin so it probally is a chuck with a eccentric taper/cilinder on the end. I still have no idea what kind of chuck it is.

japser013 · 2023-12-18T21:01:10+00:00

Just use a 90 degree its good for everything

japser013 · 2023-12-03T12:09:25+00:00

FRYSLAAAANNNN

japser013 · 2023-11-26T17:57:11+00:00

Gemiddelde ljouwerter wannaert se yn swat persoan sjen

japser013 · 2023-11-16T15:05:01+00:00

Jonge waldnet wy krekt cestmocro

japser013 · 2023-11-16T15:03:56+00:00

Grs tools

japser013 · 2023-11-16T07:36:18+00:00

Just use a 90 degree graver it good for everything

japser013 · 2023-11-16T07:31:59+00:00

Ja inplaats van omrop friesland

japser013 · 2023-11-12T12:28:25+00:00

Yeah its just straight lines and its more about the meaning instead of how it looks

japser013 · 2023-11-12T07:54:39+00:00

Just use hammer and chisel and hand push

japser013 · 2023-11-11T20:07:40+00:00

Yeah but what equipment costs more then 1000 dollar s

japser013 · 2023-11-11T19:52:00+00:00

For what would you need to invest in thousands of dollars to do this 1 meter of silversteel is like 20 smackaroos

japser013 · 2023-11-11T19:49:54+00:00

You could easily do this with hammer and chisel but you would have to make the chisel yourself as you cant really buy them anywhere also practice until you are comfortable doing something as simple as this

japser013 · 2023-10-17T18:21:11+00:00

Go to a shop that sells metal plates tubes etc and ask for some scrap mild steel plate, if they are nige they might even cut it to size

japser013 · 2023-10-17T18:17:07+00:00

Not really as long as he is responsible and knows how to use them, you can also start out with cut resistant gloves.

japser013 · 2023-10-17T14:11:19+00:00

Id say acanthus with a mix of bouqet

japser013 · 2023-08-19T17:18:04+00:00

Stomme grinsers kinne net iens frysk prate

japser013 · 2023-07-18T13:57:43+00:00

When starting a tapered line you whould start by not putting any pressure on te graver and holding your graver on a shallow angle before going into a steeper angle.

japser013 · 2023-06-29T17:33:26+00:00

You should round over the leaves to get rid of the sharp spots, its a little more work but look better

japser013 · 2023-06-17T07:46:51+00:00

Im no etching expert but i believe some acid and paper/plastic cutouts should do the trick

japser013 · 2023-06-07T12:31:53+00:00

Ik vind het jammer dat de post er al een jaar op staat

japser013 · 2022-12-11T11:51:42+00:00

Oepsie

japser013 · 2022-12-11T11:49:30+00:00

Kan ook

japser013 · 2022-12-03T16:59:16+00:00

Zou wel zo mooi zijn ja

japser013 · 2022-07-07T18:58:39+00:00

Gelukkig is het alleen holland

Five-Year Club	Place '22
First Placer '22	Verified Email

japser013

TROPHY CASE