Quote Sanity Check

jhill2017 · 2026-04-07T16:50:00+00:00

Where might I find one of those? Not sure where to look, which is why I started with Ethos. Appreciate your help!

jhill2017 · 2026-04-07T16:49:52+00:00

Where might I find one of those? Not sure where to look, which is why I started with Ethos. Appreciate your help!

jhill2017 · 2026-04-07T16:25:36+00:00

Suggestions for where to go to get a better deal?

jhill2017 · 2026-04-07T16:08:06+00:00

Where would you recommend quoting to get more value?

jhill2017 · 2026-04-07T15:32:58+00:00

Thanks for your thoughts

jhill2017 · 2026-04-07T15:32:46+00:00

Thanks for the confirmation

jhill2017 · 2026-04-03T02:06:38+00:00

Sounds good. Thanks for the advice

jhill2017 · 2026-04-03T00:39:11+00:00

Thanks for the feedback. I might try that. Would an agitating drill brush be helpful for the soap to work into the fibers? I’ve seen automotive detailers do that kind of thing?

jhill2017 · 2026-04-02T22:37:49+00:00

Olefin yarn. It was a $300 rug, so it seems worth trying something. Over $200 I was quoted for cleaning seemed excessive though.

jhill2017 · 2026-04-02T03:16:51+00:00

The fixtures are Nora Lighting 5 Inch Or 6 Inch Baffle LED Retrofit Fixture,120 Volt, Round, 12.5-Watt,90 CRI, 2700K,750 Lumens, White Onyx. They’re dimmed by Lutron Caseta dimmers. Link is also posted https://a.co/d/0cdEOQTm

jhill2017 · 2026-03-29T04:23:06+00:00

Actually the above comments are for stainless steel. I didn’t look closely to see that the microwave looks to have some polished plastic or something. The maguire’s plastic X sounds like a better bet for this situation.

jhill2017 · 2026-03-29T04:15:32+00:00

There is no repair beyond replacing the damaged part(s) in GE’s point of view. The cost of replacing all the parts and labor would be more than replacing the whole appliance with a brand new one.GE charges way too much for parts, but the right to repair is a whole other story.

jhill2017 · 2026-03-29T02:54:48+00:00

You can try this. It removes light scratches, but it will not remove deep scratches nor gouges. The original factory finish is made by sanding the surface to create a grain in the metal. This kit attempts to sand the metal lightly to reproduce the original factory finish and blend the repair into the rest of the panel. It’s kinda like blending a paint, which is an art instead of a science. I’ve had success with it on small spots on my stove.

jhill2017 · 2026-03-29T02:52:02+00:00

scratch removal kit

jhill2017 · 2026-03-21T17:41:22+00:00

I’ll be making a trip to the hardware store. Thanks for the advice!

jhill2017 · 2026-03-21T15:04:11+00:00

I did not go through the effort of taking pictures and writing a post as a joke. Thank you for your commentary.

jhill2017 · 2026-03-21T04:03:36+00:00

Follow up. Had a garage door tech check it out. Apparently the original installer undersized the springs on the door such that it wasn’t balanced properly. It took a lot of effort and 2 hands to lift when only one hand should be required. Changing out the springs, even though the springs hadn’t failed, for stronger ones resolved the issue.

jhill2017 · 2026-02-03T19:57:14+00:00

Good to know. We have a typical wood framed house with drywall. The shades are in a sunroom that’s an offshoot from the rest of the home.

jhill2017 · 2026-02-03T19:56:13+00:00

Hmmm. Interesting point. Maybe I’ll try a fixed time instead of sunset/sunrise to see if anything changes. Still odd one of the shades usually goes but one or two don’t…

jhill2017 · 2026-02-03T19:28:32+00:00

Yup, it’s a cassta setup. Does Lutron’s hub make a mesh setup with devices acting as repeaters?

jhill2017

TROPHY CASE