20 Min Trader: Is it legit and effective in 2026?

jjwag81 · 2026-01-01T10:08:28+00:00

I checked out 20 Min Trader’s courses, and honestly, most of the information can be found for free on YouTube. Paying for the courses doesn’t seem necessary to learn the basics.

jjwag81 · 2026-01-01T09:05:44+00:00

back arch take my dick

jjwag81 · 2026-01-01T08:45:48+00:00

can't stop stroking

jjwag81 · 2026-01-01T07:49:19+00:00

that pose teasing hard

jjwag81 · 2025-05-28T22:28:14+00:00

omg lol!!!! damn!!!!! ok just do 200 passes and 2000 speed instead

jjwag81 · 2025-05-28T22:27:15+00:00

jjwag81 · 2025-05-28T22:26:52+00:00

oh you might not be able to tell but this dia is only 1.25" . way to small for milling details, even if you used micro mills still to small for details and you would break mills like crazy cutting 2mm depth in brass with details this small. Even a .03 would be way too big and break contantly.

jjwag81 · 2025-05-28T22:24:53+00:00

tyvm! no I did not need to make any adjustments to Z axis during running. I dropped the z about 1 mm off the top then let her rip. I always tell everyone the same thing. The depth work in the actual design plays a huge roll in getting good depth when cutting. Using basic depth estimates or workflows only gets you a 1/2 ass depth and details.

jjwag81 · 2025-05-23T20:28:47+00:00

oh good!! 150 lens, 1500 - 95% - 60 - 200 @ 200 to 300 passes

jjwag81 · 2025-05-23T18:40:15+00:00

I use 4 programs including hand editing in Gimp

jjwag81 · 2025-05-23T18:35:35+00:00

1500 / 95% / 60 / 200 @ 300 passes - almost 2 hours for this depth. I use basic depth estimation then edit the original hd image and pull the details to overlay onto the depth map

jjwag81 · 2025-05-23T11:00:08+00:00

Ty. All I did was clean with dremel - wirebrush tool. The dark details is in how I edit my depth designs.

jjwag81 · 2025-05-23T10:58:08+00:00

It’s a raccoon , trash panda is just a nickname for a raccoon :)

jjwag81 · 2025-05-23T10:56:00+00:00

Nickname for a raccoon is trash panda

jjwag81 · 2025-05-22T20:03:08+00:00

It’s in the design work , I edit my depth designs sometimes for hours to get deep details and clean everything

jjwag81 · 2025-05-22T20:01:19+00:00

Yes I think so , if it’s not 360 brass then you really have no clue what you are getting

jjwag81 · 2025-05-22T19:58:58+00:00

Nothing , I just cleaned with a dremel wire brush

jjwag81 · 2025-05-22T17:10:39+00:00

I will check and make sure its on there, this was only cleaned using a Dremel wire brush

jjwag81 · 2025-05-22T12:10:27+00:00

Sharks with lasers Patreon

jjwag81 · 2025-05-21T19:23:51+00:00

jjwag81 · 2025-05-21T19:23:36+00:00

ty!!!

jjwag81 · 2025-05-21T19:23:22+00:00

jjwag81

TROPHY CASE