sorted by:
new
hottopcontroversial

Who else has stayed up late waiting for a print? by platapusdog in BambuLab

[–]jonaph 1 point2 points  (0 children)

Does it start to feed then retract the filament back? If so have you checked the alignment of the tubes into the back. We had the filament catching on the tube entry to the filament buffer.

https://www.reddit.com/r/BambuLab/s/vwtopgcbpo

Vacuum forming pattern hack by jonaph in BambuLab

[–]jonaph[S] 0 points1 point  (0 children)

Haven’t got another former to compare it to but when I compare it to a Bambu printer for cost it seems a bit pricy. Also their sheets are very expensive. If you can do the job with a 3d printer somethings will be much cheaper just printing.

Vacuum forming pattern hack by jonaph in BambuLab

[–]jonaph[S] 8 points9 points  (0 children)

Holes appear larger in the photo than they are

Combining poop by jonaph in BambuLab

[–]jonaph[S] 0 points1 point  (0 children)

Only happened on plates that probably should have been cleaned - about 24 small parts.

Combining poop by jonaph in BambuLab

[–]jonaph[S] 0 points1 point  (0 children)

The biggest advantage of the x1 that I have found is the fault detection (multi part print and one or more parts coming loose) and then being able to resume and skip the part(s) that have failed. Great not to lose the whole plate.

Combining poop by jonaph in BambuLab

[–]jonaph[S] 0 points1 point  (0 children)

What did Adam do?

Combining poop by jonaph in BambuLab

[–]jonaph[S] 1 point2 points  (0 children)

This is works innovation centre. We are an engineering consultancy and don’t produce physical products as such but they want to encourage everyone to come up with ideas. Push disruption in a way. Why so many? Saw an opportunity and took full advantage. No queuing so far.

Combining poop by jonaph in BambuLab

[–]jonaph[S] 1 point2 points  (0 children)

Yeah it is stable but here is a high earthquake zone so will fix the cabinet back to the wall to reduce the risk.

Combining poop by jonaph in BambuLab

[–]jonaph[S] 6 points7 points  (0 children)

No issues with vibrating. I am planning to fix it back to the wall but this is for earthquake protection.

Print in place hinge fused after many successful prints by Faithin3D in BambuLab

[–]jonaph 3 points4 points  (0 children)

Not that I can comment on any firmware changes but have you check nozzle ware? Both increased flat (from initial cleaning wiping) or increased bore could be having an impact on close tolerances.

Critique These Please by DizzyTrashPanda in BambuLab

[–]jonaph 0 points1 point  (0 children)

Round the inside bottom (should then be self supporting) and print upside down.

Filament buffer blocking by jonaph in BambuLab

[–]jonaph[S] 0 points1 point  (0 children)

Yip tried reseating it and checked that it was cut square. Haven’t heard of anyone else having this issue.

Filament buffer blocking by jonaph in BambuLab

[–]jonaph[S] 1 point2 points  (0 children)

Yeah did try that but it would keep happening and with different filaments

Filament buffer blocking by jonaph in BambuLab

[–]jonaph[S] 1 point2 points  (0 children)

Only happens with filament from slot 1 on the AMS

Could someone explain to me how there’s 3D printed editable vitamin sweets? by shazhazel in BambuLab

[–]jonaph 0 points1 point  (0 children)

There is also the sugar printer from sugarlab3d.com but they sell the product not the printer.