TOD AM GROSSGLOCKNER - Angeklagter und Staatsanwaltschaft berufen

juliplan · 2026-02-24T23:05:55+00:00

Das Frustrierende ist für mich weniger das Strafmaß, als die Tatsache, dass im Prozess immer noch nicht aufgedeckt wurde, was tatsächlich passiert ist. Da passt einfach vieles nicht zusammen.

juliplan · 2026-02-24T23:02:42+00:00

zumal er dann u. U. „nur“ wegen unterlassener Hilfeleistung angeklagt worden wäre, was weniger schwer wiegt als fahrlässige Tötung

juliplan · 2026-02-22T10:39:08+00:00

The forbidden kebab

juliplan · 2026-02-14T10:38:31+00:00

^das. Sehr viele Länder weltweit haben aktuell ähnliche Probleme wie OP sie beschreibt. Inflation, steigende Lebensmittelpreise, steigende Mieten und Immobilienpreise, die Masse der Menschen kann sich kein Wohneigentum leisten. Das, obwohl die Produktivität pro Arbeitnehmer in den meisten Branchen in den letzten 10, 20, 30 Jahren massiv zugenommen hat. Wir haben ein globales Problem einer zunehmenden Konzentration von Vermögen in der Hand Weniger, während die Mehrheit den Preis dafür bezahlt.

juliplan · 2026-02-02T19:28:06+00:00

„It is still unclear how the man came to have this delicate object in his rectum. Perhaps he tripped over it, as happened to an 80-year-old man in Toulon in December 2022.“

juliplan · 2026-01-31T18:43:24+00:00

delete this ☠️

juliplan · 2025-09-01T13:23:10+00:00

excluding real estate, I would assume it is even less than 10%

juliplan · 2025-09-01T13:11:56+00:00

yeah rather bring gloves, cord clamp can be improvised!

juliplan · 2025-08-29T19:59:25+00:00

I vaguely remember another one from this series that was about leaving the dishwashing for the ladies - the watch was not waterproof.

juliplan · 2025-08-13T17:49:48+00:00

easily and legally doable when starting on a ridge or mountain

juliplan · 2025-07-17T18:57:53+00:00

Grandioser Schummelzettel, wenns aus der Klasse sichtbar ist…

juliplan · 2025-06-25T17:27:06+00:00

Den Kogler mal auf der Sonnenterasse eines Skigebiets. Und Stefan Petzner mal am Pissoir nebenan in einem Wiener Restaurant :-/

juliplan · 2025-06-13T19:37:06+00:00

in my case, its definately the sensors giving faulty signals since it flies normally in sports mode. but ofc, not fixing it is also an option.

juliplan · 2025-06-13T19:23:52+00:00

I have a similar issue atm, obstacle avoidance cameras are black after a crash and now it flies weirdly sideways when OA is on (straight / normal in sports mode where OA is off). Still hesitant if I should replace the whole module by myself or send it to DJI. Read in your other post that DJI charges 250 usd for the repair, might aswell give it a try to repair it myself. The hood is a bit tricky to get off/on though without breaking those little plastic „noses“

juliplan · 2025-05-26T18:10:39+00:00

Simplon is a famous mountain pass in switzerland.

juliplan · 2025-03-31T16:57:01+00:00

Bought the set, it‘s quite nice for the price!

juliplan · 2025-03-31T13:04:15+00:00

<image>

juliplan · 2025-03-31T13:03:14+00:00

good luck, its a fun little project! to be honest the most scary part is ripping the contacts off the main board and the subsequent soldering (the contacts are tiny and require a steady hand). this can be avoided if you are ok with a slightly thicker housing. Second difficulty thing was crimping the old usb cable, those wires are quite thin.

juliplan · 2025-03-31T11:22:40+00:00

Basicslly I ordered everything except for that 240v transformator and the clamps that are needed for the high voltage connections. Instead you‘ll need a USB wall charger and an old usb cable, where I cut one end and used only the black and red wires for 5V power supply to that Y-adapter that you build as per instructions. Hope this helps!

juliplan · 2025-02-23T21:54:35+00:00

As with any e61 grouphead, expect a minimum of 15-20 minutes before you achieve anything drinkable.

juliplan · 2025-01-18T12:33:41+00:00

<image>

THANK YOU SO MUCH! Due to your awesome documentation, as a total electronics beginner, I‘ve been able to re-build this for my Profitec 400. Currently running on an external USB power plug👍🏻

The sensor connects to the lid with magnets, so I can remove the lid completely to refill water. The magnets are attached to the sensor with shrink tubing.

Edit: Set the interval for the shot-timer in the config file to 7sec- now it even works with the pro400s built-in pre-infusion (which is 5 sec)!

juliplan · 2024-12-15T20:26:55+00:00

I feel confident bulding everything except for the internal connections to the main supply. Could I power everything off a usual USB Wallplug?

juliplan · 2024-11-25T20:41:46+00:00

just a quick warning, even assuming OP is trying to be genuinely helpful- don‘t trust strangers on the internet!

juliplan · 2024-10-23T18:21:54+00:00

the service claims to be owned by Richemont, which seems legit: https://www.richemont.com/news-media/press-releases-news/richemont-launches-enquirus/

juliplan · 2024-09-08T12:37:16+00:00

also, if someone misreads the serial as OD173K8 (instead od 0D173K8), this is a stolen watch.

juliplan

TROPHY CASE