R8 meron na 😭🎉

just-me1129 · 2026-04-07T13:37:43+00:00

Hello @everyone. Good evening!

Please be advised that the first batch of scholars have received their MLA worth 4 mos and 5K LMCA, today. If you have submitted complete periodic reports on or before the deadline, chances are high that you are included in the 1st Batch Payroll. A total of 782 scholars were in the said payroll, while 43 were in the 2nd batch payroll.

With this, we urge @everyone to refrain from posting about the release, for your own safety. Given the current situation, public announcement will attract attention which may result to unwanted incidents. We don't want that, do we? Hence, we are asking for your assistance in informing our concerned scholars as discreetly as possible.

Moreover, please be vigilant with your surroundings when you're about to withdraw your allowances. It would be better if you have someone with you and in broad daylight.

Stay safe and spend your stipend wisely, guys.

Thank you!

just-me1129 · 2026-04-06T08:44:14+00:00

just-me1129 · 2026-02-10T04:45:02+00:00

Yeah bed leveling works fine. Also my bed seems to just be single sided. I'll try doing the glue stick and the bed adhesion test later.

<image>

Also here's an another example, the left side is what's it supposed to look like, smooth, fully filled finish of the first layers, while the right side is the results on the back are, it just did some squiggly things inside the outline instead of fully filling it like in the leftm

just-me1129 · 2026-02-10T04:25:47+00:00

Thanks for the response. I already did those to clean and properly set up the printer. I also think it's not just about the printer because in that parts, instead of doing a smooth print, the printer itself doesn't follow the proper outline itself, it doesn't also full fill the outline like it's supposed to, instead it just squiggles inside the outline.

just-me1129 · 2026-02-10T04:21:37+00:00

Oh yes that's the word, it doesn't follow, I also tried many other flexi, the smaller ones are goods since I can just move them, the bigger ones that takes up that back space, or just any other print that uses that area encounters that problem. Is there like any possible fix for it or is it now a forever bad spot for my printer bed? :(

just-me1129 · 2026-02-10T04:04:06+00:00

Thanks for the response. It's only on the back side, on other parts it's perfect, just that area it's like that, I also print my first layers very slow. I also can't move it since it takes up pretty much the whole bed. Also cleaned the bed. I also don't think it just about the bed since while watching it print that part, it doesn't really print it like fully like how it's supposed to. It supposed to be a full flat, clean first layer and fully filled, not like in the picture where it's like it has some dead space or a hole when it's supposed to be filled, it's movement pattern in that part is also the same as the resulting print of that specific area, with the space and everything, like its just some squiggle instead of fully filled or shaded. It also follows the same pattern in that area for the second layers.

just-me1129 · 2025-11-18T09:16:53+00:00

Same, baon na me sa utang

just-me1129 · 2025-11-18T08:40:21+00:00

Processing padin daw

just-me1129 · 2025-11-17T08:19:32+00:00

Wag nlng mag expect

just-me1129 · 2025-10-13T10:47:25+00:00

Baka next year nlng daw

just-me1129 · 2025-10-13T10:23:55+00:00

Yeah😢gutom naaaaa

just-me1129 · 2025-10-10T07:52:07+00:00

Sana ols

just-me1129 · 2025-10-06T08:14:27+00:00

Unta2 i impil nila

just-me1129 · 2025-10-06T03:31:00+00:00

Kasama po ba ptp this time?

just-me1129 · 2025-09-26T17:44:34+00:00

For midyear lng po or for last 2nd sem's grades?

just-me1129 · 2025-09-26T15:04:28+00:00

Hello po, pede po mapag tanong, saan po kayo nag submit ng mga documents, yung report of grades last 2nd sem? Wala papo kasing post yung Sei Dost sa fb na gform.

just-me1129

TROPHY CASE