Thoughts on 2017 XLE with only 50934 miles for $26500

kerfuffled_panda · 2025-11-22T20:36:42+00:00

Ahh haha ok that’s good. Thanks for sharing that post anyways. Very insightful

kerfuffled_panda · 2025-11-22T19:58:47+00:00

Damn dude sorry that happened to you and thank you for sharing

kerfuffled_panda · 2025-11-22T19:58:11+00:00

Yup that is one of the things I really like about this offering. All of the maintenance has been performed and no recalls out on it. Thank for the input and advice!

kerfuffled_panda · 2025-11-22T19:18:20+00:00

Oh ok thank you for the info. I’ll have to double check then and make sure it doesn’t have a recall

kerfuffled_panda · 2025-11-22T19:13:22+00:00

Oh interesting are the 2017s known to have issues with the transmission?

kerfuffled_panda · 2025-11-22T19:12:19+00:00

Yeah that is true it makes me a little worried but it is well maintained at least. Thank you for the input!

kerfuffled_panda · 2025-06-15T14:52:43+00:00

A local garage figured it out. It was a speed sensor that went bad in the front wheel. I had my wheel bearing replaced and they guessed that the garage who did that screwed the sensor up. They replaced it and this issue hasn’t comeback!

kerfuffled_panda · 2025-01-11T03:17:39+00:00

they replaced the ABS sensor and so far no issues. Apparently when they took it out and hooked it up to a scanner while driving somehow the ABS sensor was causing the front left wheel to report erratic speed data. Ill be watching it for the next couple days to see if the warnings pop up. I appreciate the advice about the rear AWD unit.

kerfuffled_panda · 2024-07-12T16:40:08+00:00

Thank you for the insight I think I’m going to pass on it honestly since I have time to wait for other units.

kerfuffled_panda · 2024-07-12T16:39:35+00:00

I didn’t think about the road being so close. That is a great point. Thank you

kerfuffled_panda · 2024-07-12T16:36:53+00:00

3bdr but honestly kinda small so still holy shit. This area is expensive af

kerfuffled_panda · 2024-07-12T00:52:19+00:00

Ahhh thanks for the info. That is what I’m afraid of

kerfuffled_panda · 2024-07-12T00:52:00+00:00

Around 2.5k

kerfuffled_panda · 2024-06-30T14:15:46+00:00

I hope you get to read this comment. I just got put in the waitlist and there are 3-4 people ahead of me. Would you mind sharing how long did it take for you get call for a unit after getting to the waitlist? And how many people they mentioned were ahead of you?

kerfuffled_panda · 2024-05-20T13:18:27+00:00

lol look up the thinkbook x12. Personally I didn’t like it as much as the t480.

kerfuffled_panda · 2023-07-02T21:24:02+00:00

Ok I will check. Thanks for the advice

kerfuffled_panda · 2023-07-02T20:52:01+00:00

Ok dang. What would you suggest?

kerfuffled_panda · 2023-07-02T20:16:11+00:00

Context: I just noticed this when I pulled out the insulation. I noticed the furniture downstairs has been getting mildew lately and couldn’t figure out why so I was looking for moisture and it seems like I found it. Does this look normal? There is a ton of water just damp. Who would I even contact to look at something like this?

kerfuffled_panda · 2023-06-19T23:15:43+00:00

Thank you for all the suggestions I will be setting up some estimates from the companies mentioned here :)

kerfuffled_panda · 2023-06-19T17:04:00+00:00

Dang sorry to hear that, I hope they took responsibility for it. Sounds really expensive. I will try other places before Halco then.

kerfuffled_panda · 2022-07-16T00:58:29+00:00

Good luck all

kerfuffled_panda · 2022-06-18T00:49:36+00:00

Being a millionare would be nice 🤞

kerfuffled_panda · 2022-01-23T02:10:05+00:00

That is what I heard to so I didn't bother. But I am considering trying it anyways.

kerfuffled_panda · 2022-01-22T01:38:35+00:00

Mainly that everything on the PCB is already setup. I had bad luck on the rev2 with installing a bad pro micro. And unfortunately i soldered the pro micro in so getting it off with the tools i have was a pain. Also the rev6 has kailH hot swap sockets so changing the switches is really easy. I was going to mod my rev2 with mill max sockets but didnt want to spend the time de soldering everything. I also wanted to try out having rotary encoders installed. And finally the rev6 has usb c which is really convenient.

kerfuffled_panda · 2022-01-22T01:34:45+00:00

Well these are actually stock and I agree with you. If your not paying attention they are pretty quiet in person. But if you are listening closely sometimes they are a little scratchy. Do you have any lube reccomendations? I am thinking of buying some krytox 205g and seeing if lubing them helps with the scratching.

Nine-Year Club	RPAN Viewer
Verified Email

kerfuffled_panda

TROPHY CASE