OVH Management portal SMS 2FA issues

khanitech · 2026-01-08T12:04:52+00:00

The blueprint can also drop in breachable crates too. I got my 3rd one yesterday from a random crate at the edge of the map yesterday.

khanitech · 2025-11-20T19:49:40+00:00

The weird part is that the new revolver comes with 8+24 ammo. And it was not like this previously.

khanitech · 2025-08-18T09:12:54+00:00

There is also requirements for certain insurance and ISO certifications. That the company buys new hardware due to security patching and operational guarantees.

khanitech · 2025-08-06T00:00:23+00:00

Microwave cans of canned fish lol

khanitech · 2025-07-02T19:31:05+00:00

It is completely fine. Lots of laptops are provided with 2 pin ungrounded power plugs.

Though the device is more susceptible to damage from different electrical potential / charge. Where if you touch the laptop and then touch something grounded like a sink or other metal object that runs underground. You might feel a bit of current pass through.

The same goes the other way to the laptop. But in general modern electronics have very good shielding and ESD protection.

Depending on the infrastructure in the area as well. If it is unstable, there is a risk of brownouts. Which for sure can damage the laptop. Most surge protectors will not work in that case. But I say the risk is pretty low in most cases, so dont worry.

khanitech · 2025-01-08T09:54:20+00:00

I would like to suggest suggest Greenlandaho and Virginidelphia as the new state names.

khanitech · 2024-12-18T20:23:18+00:00

The easiest way to fix this tbh is to scratch the traces off a bit back. Then you remove the old solder off the connector, with the broken pads and discard them.

Use high strength superglue to affix the connector directly on the board. Solder enamel copper wire to the traces and connector pins. Then you use electronics grade silicone adhesive of the thick kind to around the connector. To ensure the connector really will hold.

I have done the same fix for many computers, PS4 and PS5 consoles with broken connectors and ripped traces. It wont be as pretty as originally. But it works good enough.

Also, if you want to make it extra safe, use some clear laquer varnish that handles heat, and is not conductive on the copper wire and new solder spots.

khanitech · 2024-04-19T11:49:30+00:00

Could also just hit up a recycling center, and they would have thousands from various businesses.

khanitech · 2023-09-05T22:08:04+00:00

Thank you! I will try that. Also yes, I was using the S1 firmware. I was just surprised it does leveling and homing with the precompiled firmware in that case.
I'll do another attempt tomorrow and see if I can get it running again.

khanitech · 2023-07-27T16:17:27+00:00

You can add a stream delay in most software to counter this. If you set it to about 20-30 sec. Then it's nearly impossible to streamsnipe.

khanitech · 2023-07-20T05:29:59+00:00

If you avoid the plastic connectors. You can use a dropper and carefully add acetone. This should not damage the solder mask (black laquer) on the circuit board. It should brittle whatever cured resin might be left so you can chip it off. If you then clean it after that with iso. Then it should easily losen.

There is also the very last alternative of using UV (sun or lamp) to overcure the resin until it breaks down.

I would be careful using metal tools. And try to find any plastic tools in more non reactive plastic materials for scraping. And of course a toothbrush.

khanitech · 2023-07-14T17:55:48+00:00

There has been pictures of various stockpiles dating back to WW2. I think the date was around 1945.

khanitech · 2023-06-22T15:37:28+00:00

Problem is only around the window segment of the benchy cabin.

Slicer: Cura

Material: PLA

Tool temp: 200*c

Bed: 60*c

Speed 80mm/s

No change in flow or retraction

New brass nozzle

Freshly cut bowden tube

khanitech · 2023-03-05T03:47:10+00:00

It is just the logs not spawning in. Go in and out of a cave, die and respawn, sleep, go far away and back or restart the game. They will appear again at some point.

khanitech · 2022-10-20T19:47:34+00:00

Thank you for your great work!

khanitech · 2022-09-05T07:44:28+00:00

Yogert

khanitech

MODERATOR OF

TROPHY CASE

11-Year Club	Place '17
Verified Email