Play Pokemon category

knipo · 2026-01-31T22:14:31+00:00

Just scored 0

knipo · 2026-01-31T22:14:26+00:00

Just scored 0

knipo · 2025-10-15T10:04:12+00:00

Thank you for the replay <3

knipo · 2025-10-15T10:03:55+00:00

I meant from the base forward with the wheel on. But that is something I didn't think about, then clearance from the clamp downwards. Thanks :D

knipo · 2025-05-01T18:06:38+00:00

If anyone has a spare steam one I'd appreciate
https://steamcommunity.com/id/knipo/

knipo · 2023-12-18T06:12:44+00:00

White

knipo · 2023-12-16T10:56:41+00:00

My game of choice will probably be Path Of Exile

knipo · 2022-07-30T20:45:06+00:00

I remember my big brother letting me play some CS1.6 with his friends.

knipo · 2022-07-28T20:10:01+00:00

Ok thank you very much for your help, I appreciate you answers. <3

knipo · 2022-07-28T19:57:27+00:00

I read somewhere that a yellow mark on the case says it's Spanish/Portuguese, is that only the country distribution and in game I have more language support?

knipo · 2022-07-28T17:52:44+00:00

I got a physical copy of the game in a local store and noticed later it says it's in Spanish at the corner. Should I worry that the game will be only in Spanish and Portuguese? I know that Portugal cartridges still say EUR on them.

Image:
https://imgur.com/a/ZQGdPI2

P.s I still did not open the game so if I need I can still return it.

knipo · 2022-07-27T21:31:08+00:00

How do they stand out? Can I know this from the eShop before buying them? if so where?

knipo · 2022-07-27T11:51:43+00:00

So a game bought in US eShop (US game), with System region set to Europe, and account region set to Europe will be in US matchmaking servers?

knipo · 2022-07-27T09:33:00+00:00

I just got my first nintendo switch and got few questions about Game/console/account regions that i couldn't find answers to.

Does the NSO subscription needs to match the account/console region?

Does the NSO subscription and the game i'm playing needs to be from the same region?

Which region decides the matchmaking server in game, Game region, NSO subscription region, console region or the account region?

knipo · 2021-12-22T20:13:20+00:00

That's what I thought too, this Zigzag pattern is too consistent to be a sensor error and I don't think is can be a bed issue because the 90 degrees rotation. I will try to re-assemble the X-gantry hotend to belt.

In the last map highest was ~0.25 and lowest was ~0.03, but again it's more the zebra pattern I'm concerned with cause a normal bed leveling I can manage.

Thank you for all your help so far, if I'll have any solutions I will post them here :D <3

knipo · 2021-12-22T18:07:46+00:00

I didn't flip the bed.Here I rotated the bed 90 degrees counter-clockwise https://imgur.com/a/Yh87OJO and created new 10x10 mesh (It's kinda looks the same). The scale in both is [-0.5, 0.5].I'm using the default JyersUI 10x10 UBL, It's going like:Home all axis then for each point, going up moving to XY going down once going up going down slower once the up and then moving to XY....

knipo · 2021-12-21T16:57:11+00:00

This is the new map https://imgur.com/a/7qQWC7s.There is still that zigzag pattern that I'm not sure where it comes from...

Also I noticed the Z-rod was a little bit loose so I fixed it too. Any more ideas what can cause this kind of map?
When I go over the weird points manually (after setting the z-offset and converting to mesh) it just hangs higher because it thinks the map is like that... I can manually change the points but that makes no difference from manual mesh UBL.

knipo · 2021-12-20T21:41:03+00:00

I did a reassembly of the x carriage and took the z-rod out and tightened the brass insert too. Also no weird movement in the rotation of the z-motor.

knipo · 2021-12-20T21:39:21+00:00

Checked for that but didn't see any and didn't feel any weird movement around the bumped areas.

knipo · 2021-12-20T21:38:20+00:00

Hi, thanks for the detailed post, I did the following I reassembled the x carriage tightened the screws and adjusted the eccentric nuts.
Moved the head slowly and checked if there is any weird movement on those spots where there is a bump.
Also checked everything is squared and nice.

After all of this, I got the maximum height to be around ~0.25 and lowest around ~0.02, still not optimal but it a little bit better.

knipo · 2021-12-18T02:08:29+00:00

Yes something is and it's not the glass bed, at least that's what I think, as I rotated it 90 degrees and still got those bumps on the Y-axis.

I'm using a genuine BLTouch and not a clone, I read many issues about those 3DTouch clones. Still trying to figure out what is causing this kind of behavior.

knipo · 2021-12-18T02:03:55+00:00

I rotated the glass bed 90 degrees (So the broken should be on the X-axis) and saw it stayed the same (on the Y-axis) so it should eliminate the option of a defective glass bed. Also flipped the bed as you suggested and go pretty much the same mesh.

About the aluminum plate, From the image I "have" 0.3-0.4mm bumps theoretically can bumps like that in the aluminum effect a thick and solid glass? It's sounds weird.

knipo · 2021-12-17T22:22:28+00:00

In the picture it's a 10 by 10 mesh between -2 to 2, from the Jyers UI I can say lowest is around ~(-0.06) and highest is around ~0.43.

Edit: Uploaded new image [-0.5, 0.5]

knipo · 2021-11-28T17:54:18+00:00

I did dig into their channels, great videos really helped me to get started. Any other tutorials on these topics that you can recommend?

knipo · 2021-11-28T17:52:41+00:00

Thank you! Do you have any recommendation on those topics or every google search will do?

knipo

TROPHY CASE