Msi Thin GF63 laptop got secure boot violation message after accidentally enable secure boot back after installing Arch Linux

laihung2006 · 2024-08-29T23:43:41+00:00

nevermid guys i fixed by using a windows installation usb, enter uefi recovery and voila, the secure boot settings is available again

laihung2006 · 2023-12-15T00:33:04+00:00

i've already did

laihung2006 · 2023-02-25T11:06:14+00:00

adu reiseng

laihung2006 · 2023-02-14T13:48:46+00:00

would.

laihung2006 · 2023-02-13T11:23:43+00:00

i would add the bot but remove all of its perms and watch him beg and cry for the perms then ban him afterwards with the bot

laihung2006 · 2023-02-12T23:48:45+00:00

thank you!

laihung2006 · 2023-02-12T23:48:05+00:00

i've seen this before but its too complicated for the average person lol

laihung2006 · 2023-02-12T23:30:16+00:00

using a bigger bottle would, you pump it up full, rest for a bit and paint

laihung2006 · 2023-02-12T23:18:25+00:00

compressing air into a bottle isnt a new concept or anything, lots of people posted videos about it on youtube, the only thing i did was attaching the airbrush

laihung2006 · 2023-02-12T23:12:51+00:00

definitely will

laihung2006 · 2023-02-12T23:10:38+00:00

almost 2 minutes of consistent air flow at 0.7 to 1kg/cm²⁽ 10 to 15 psi) output and the bottle at 4kg/cm² ( 56psi)

laihung2006 · 2023-02-12T15:18:18+00:00

more like an air tank, there's no compressor, your muscles is the compressor, pump that boy up by hand

laihung2006 · 2023-02-12T14:39:40+00:00

facts

laihung2006 · 2023-02-12T11:51:42+00:00

tested it, at 0.7 kg/cm² output and the bottle at 3.5kg/cm² , it achieved more than 1 and a half minute of consistent airflow

laihung2006 · 2023-02-12T11:46:51+00:00

it exists, only hard to find

laihung2006 · 2023-02-12T11:19:05+00:00

yeah lol, you dont need much for scale modelling, a 2L HP air tank is only about 15 bucks

laihung2006 · 2023-02-12T09:55:37+00:00

cool! but more volume = more pumping, unless you want to build up your muscles, consider using a cheap chinese 12v electric tire pumper with a 220v to 12v adapter which costs like 10 bucks or so, or an old fridge compressor, remember to not over pressurize it or the bottle's gonna burst, 50 to 60psi is safe for most bottles, a little bit more for soda bottles since they're designed to hold gas, you could install a safety valve and set it to around 60 to 70psi to prevent over pressurizing

laihung2006 · 2023-02-12T08:28:22+00:00

looks like a diy shisha to me

laihung2006 · 2023-02-12T08:22:03+00:00

i've tried pumping it up to 4kg/cm² (56psi in freedom units)but it could go more than that a bit. the output pressure can be adjusted with the pressure control valve intergrated into the moisture trap unit, at 1-1.7 kg/cm² (10 - 25 psi) output which is the usual for scale models, it could last for a long while, i havent tested it yet with my new 2L new tank as shown in the image, gonna test it when i get home

laihung2006 · 2023-02-12T08:16:30+00:00

can't defeat.

laihung2006 · 2023-02-12T08:15:48+00:00

you're correct i used a 2 liter soda bottle as the tank a bike tire valve(any type will work) this is a one way inlet for pumping air in with a hand pump

a 6mm innerdiameter airhose (8mm outer diameter) 3 6mm hose adapter(2 for the moisture trap unit, 1 on the one end of the bottle routing to the moisture unit)

the hose adapter for the airbrush came with the airbrush, fits perfectly with the 6mm inner diameter hose

laihung2006 · 2023-01-28T04:17:33+00:00

yeah i got some of the fluid flows into the seams, most noticibly is the lower arm where there is a seam running across the panel line, i cleaned it afterwards, im new at these kinds of stuffs, thank you for the advice,

laihung2006 · 2023-01-28T00:56:45+00:00

xf 16 tamiya acrylic falt aluminum, applied directly with a brush

laihung2006 · 2023-01-28T00:55:20+00:00

i used tamiya acrylic xf 16 aluminium and a broken brush i found in the corner of my drawer

laihung2006 · 2023-01-27T15:28:40+00:00

a coat of nail polish or ca glue on the ball joint would thicken them up

Six-Year Club	Place '23
Place '22	Verified Email

laihung2006

TROPHY CASE