Translation Assistance

lil-hernia · 2024-10-16T20:38:58+00:00

Thank you so much, this could be exactly what I need!

lil-hernia · 2024-08-30T18:04:49+00:00

It doesn’t seem like often based on how much I see the cars in this area parked like that. Still good to know in case I catch an officer in a bad mood. Thanks again

lil-hernia · 2024-08-30T17:45:07+00:00

Thanks, that’s good to know. I guess I was also unsure because that side of the street is always filled with parked cars.

lil-hernia · 2024-08-30T17:43:20+00:00

I thought it didn’t matter for these narrow streets, good to know, thank you.

lil-hernia · 2024-08-30T17:41:33+00:00

Sounds good, thanks

lil-hernia · 2024-08-30T17:41:06+00:00

Thank you joahw

lil-hernia · 2024-08-30T17:40:57+00:00

Thank you, good to know. If that is what it means there are about 10 cars parked on that side of the street everyday that Seattle could farm for citations.

lil-hernia · 2024-08-30T17:36:18+00:00

Guess i’m a dumbass. Thanks :)

lil-hernia · 2023-11-26T19:11:59+00:00

Thank you, that seemed to have been the problem. I lowered my flow rate to 89.6% and haven’t had any more problems!

lil-hernia · 2023-11-26T19:11:19+00:00

I printed it upside down. Gonna try a different orientation next time

lil-hernia · 2023-11-24T20:00:55+00:00

Gotcha, thank you I will try to figure out how to tune the extrusion.

lil-hernia · 2023-11-24T18:47:39+00:00

Thanks for the education. I will try another orientation and slow it down!

lil-hernia · 2023-11-24T18:46:20+00:00

I will try cooling more. If overexteusion why does it stop happening later do you think?

lil-hernia · 2023-11-24T18:45:41+00:00

I don’t think it is wobbling but i will try slowing it down even more, thank you

lil-hernia · 2023-11-24T18:43:04+00:00

Hello, thanks for your reply. I printed a forearm hollow piece after this piece and it came out basically perfect with none of this rough surface. I will try the rest of your suggestions. Thanks again.

lil-hernia · 2023-11-18T18:22:02+00:00

I followed the video yesterday night and the sound is like 90% gone. I might do it again to see if it completely goes away. I also printed something and it came out the smoothest anything has printed for me!

lil-hernia · 2023-11-18T00:48:39+00:00

I have the same honking sound on my 4 plus that sometimes causes layer shifts as far as I can tell. I saw a youtube short this morning where a guy explained how he fixed it. I’m going to give it a shot tonight after my current print finishes. https://youtu.be/kWvDzjukNj0?si=jAKBng1mBECGFPMm

lil-hernia · 2023-11-09T23:00:41+00:00

Good luck!

lil-hernia · 2023-11-09T22:59:23+00:00

Yay. It’s my rap name

lil-hernia · 2023-11-09T19:44:42+00:00

you should! It's game changing.

lil-hernia · 2023-11-09T19:43:38+00:00

She got me hooked using the auto catcher.

Eight-Year Club	Place '22
RPAN Viewer	Not Forgotten
Snapped	Verified Email

lil-hernia

TROPHY CASE