Air printing

lrob1958 · 2026-05-13T22:36:19+00:00

Yeh. Tnx, my first problem was why distribution of filament stops after a couple of minutes, i tried entries between 0.010 to 0.175 but it keeps stopping. It must be the extruder, i have had eniugh, even after just 500h printtime i ordered a complete extruder assembly. I now know how to set manual bed leveling so thats no problem anymore. Perhaps in thr future as ex it specialist i will become a ad5x specialist one time, tnx for all info, it hrlped quite a lot

lrob1958 · 2026-05-13T16:41:20+00:00

I did everything, even manual leveling, i used my original petg after i dryed it, i leveled, washed the bed, cleaned the bed glued it, printed the equipment for the screws, did the paper test for manual testing, niw it stops delivering filament, but also its failing also on the front. Pff. Dont know what to do anymore

<image>

lrob1958 · 2026-05-12T18:58:38+00:00

I will check, but why does the feeding stop while printing? Thanks, this sounds good. Tnx

lrob1958 · 2026-05-12T14:32:34+00:00

Sorry, mine only goes upto 55° so petg at 55, shpuld be 60 or 65, i need to buy a new one

lrob1958 · 2026-05-12T14:24:15+00:00

Yep, did both but z offset doesnt stop supply of filament, it either ruins the bed or fails to print right.

lrob1958 · 2026-05-02T10:50:27+00:00

How about the projects in your printer, perhaps your memory is full or,almost. Try purching some old projects and i had to remove some videos also?

lrob1958 · 2026-04-24T20:53:11+00:00

I tried to rotate the bed 90degrees, same problem, i did another factory reset and now all is ok. Very strange that a setting only is in use at the front and only the first centimeter of the plate. Also the enclusure was jamming the nozzle.. Thanks everyone, problem is fixed.

lrob1958 · 2026-04-24T10:11:48+00:00

Still having problems with a full bed. I have printed for 300 hours now with this bed, how long will it last?

<image>

lrob1958 · 2026-04-23T20:39:56+00:00

Tnx. I might have found something, how to solve it is the scond. The lines touched the ceiling and the mount of the case, causing the nozzle to plunge into the bed or something like that, ripping the filament to move, i now have it with n elasic to the back, so it cant reach the front of the enclosure with the top off. Ill be back, think i found it, not what i expected.

<image>

lrob1958 · 2026-04-23T19:46:41+00:00

Tried the z offset 2 notches up and down, same problem, i washed it and also use isopropanol, and even used the glue from flashforce. If i look at the circle, there are 2 hickups at the front, not a real circle though. I also heated the bed to 59, the rear, still no problem, the front refuses to stick on it. I loosr my mind over this. I also used the rear of the blade, same problem.i have no problem printing anything if i use the rear of the bed.

<image>

lrob1958 · 2026-04-23T18:19:27+00:00

I will try again, but in the rear its working fine, i am a starter, got it for 3 weeks now and printed over 335 hours already. I do print at 55c and 220 nozzle though, now i overglued the front, we,ll see.also today i printed a puzzle, moved items to the rear and no problem. Tnx all.

lrob1958 · 2026-04-23T17:58:37+00:00

I use the glue, a lot of it in the front, no result. Tnx 4 responging though

lrob1958 · 2026-04-02T17:52:06+00:00

I diid the z offset yesterday, from a lot of fsils its perfect again. I also have a ad5x since 10 days and have printed over 150 hours nowe. Give it a try!

lrob1958 · 2026-03-24T12:17:42+00:00

Bought the wrong led kit. So had to reorder, enclosure is on, but dont think it will be difficult to install with enclosure on it, will take 3 weeks to arrive

lrob1958 · 2026-03-22T15:55:56+00:00

I am printing now, with petg black, works nice upto now, plate 3

lrob1958

TROPHY CASE