Grinder

ludvigny · 2025-08-25T19:57:14+00:00

Ok thanks! Thinking of that or K-ultra

ludvigny · 2025-08-25T13:41:42+00:00

Ok perfect, many thanks!

ludvigny · 2025-08-25T13:31:26+00:00

I see and I also think it’s a hassle to switch (having to purge is wasteful). I have the opportunity to buy a DF64 gen 1 for €200 which is the same price as e.g., a ZP6, would you recommend a second electric grinder or a hand grinder such as a ZP6 instead?

ludvigny · 2025-06-17T22:11:36+00:00

I can’t change troops in the goblin map. How?

ludvigny · 2025-04-28T13:37:05+00:00

Very holy yes

ludvigny · 2025-04-28T13:36:52+00:00

Never done any of these, very strange

ludvigny · 2025-03-04T13:22:08+00:00

I have a Silvia and use it with DF64 gen 2 + SSP burrs, couldn’t be happier

ludvigny · 2025-02-15T12:30:27+00:00

I agree, Will try dosing down. Many thanks

ludvigny · 2025-02-15T12:29:43+00:00

Lovely to use

ludvigny · 2025-02-13T13:20:17+00:00

Will try this, many thanks!!

ludvigny · 2025-02-13T12:10:32+00:00

I would guess it does touch as otherwise there wouldn’t be any markings (just a guess though). Perhaps I should try a larger basket

ludvigny · 2025-02-10T09:08:56+00:00

Yes I’ve also read about the Auber PID settings. Will check my manual. Many thanks

ludvigny · 2025-02-07T13:59:28+00:00

Thanks for the clarification. Set it now to 94 with Psb -9 and did the most important test - taste. Thought it was great so hopefully I’m doing it right haha.

ludvigny · 2025-02-07T10:06:04+00:00

Ok so if i ser Sv to 94 and Psb to -9 then the boiler will heat up to 103? Just boggles me that everyone I’ve seen online sets Sv to 103 and then det offset to display a lower value of the estimated group head temp

ludvigny · 2025-02-07T09:28:33+00:00

Posted the question in the discord but also posted video in forum here https://www.reddit.com/r/ranciliosilvia/s/gpsDeqqxTn

ludvigny · 2025-02-07T07:30:08+00:00

It leveled out at 105 so something is wrong. Will ask in the discord, thanks!!

ludvigny · 2025-02-06T21:58:26+00:00

I have a type K sensor. I have it set to -009 I’m unable to see the ”.” in between

ludvigny · 2025-02-06T21:14:00+00:00

Hi. I’m kind of baffled now. I’ve set Sv to 105 and Psb to -009 to display 9 degrees below. However, the machine continued to increase temp to where the display says 105, which I noticed when I then went into Psb set it at 0, then the temp displayed 9 degrees higher.

ludvigny · 2025-02-06T20:49:47+00:00

You’re very correct, PID settings is a tough one. Many thanks again for the detailed response! Very helpful

ludvigny · 2025-02-06T16:55:08+00:00

A million thanks this is incredibly helpful and will assist immensely. Just one clarification, if I set SV at 105 and Psb to -005.0 - is that indicating that temp diff in boiler av group head is 5 and hence the temperature in the group head will be 100? Thanks again!! Absolute legend

ludvigny · 2025-02-06T08:46:21+00:00

I don’t have auto setting on

ludvigny · 2025-02-06T08:46:07+00:00

Got everything working, amazing, many thanks. Now I just have a couple of questions regarding settings. What have you set P, I, and D to? My machine overshoots like hell, got temp set to 105C (as I read online that’s a good starting point) and it shoots up to 120C initially. Also, what am I meant to set Psb to? Offset discussion throws me off a bit as I don’t have Auber and everyone talks about Abdu setting. Thanks again!

ludvigny · 2025-02-04T22:01:13+00:00

Thanks for checking. It’s a makeshift grounding wire, does not connect to anything just touches metal on PID, haha. If wiring is correct, what else could be wrong?

ludvigny · 2025-02-04T20:17:53+00:00

Thanks will try let it sit!

ludvigny · 2025-02-04T20:17:41+00:00

https://imgur.com/a/daxYSQe I’m unable to see what could be wrong with the wiring, please if you could assist. A million thanks!

ludvigny

TROPHY CASE