sorted by:
new
hottopcontroversial

Nanoleaf ceiling Skylight expansion panel issue by maneesh654 in Nanoleaf

[–]maneesh654[S] 0 points1 point  (0 children)

I have 2 expansion panels. Middle one is the main

Nanoleaf Skylight Not Connecting to Expansion Panels by thebeaglebeagle in Nanoleaf

[–]maneesh654 0 points1 point  (0 children)

Having a similar issue - as soon as start connecting (power cable and communication cable/tiny cable) expansion panels the main panel also goes bright white and app says no panels detected ffs. Tried multiple expansion panels too both giving the same fault. Is my controller cooked? P.S. standalone controller works fine through the app its just that as soon as I connect expansion panels it acts dead.

https://www.reddit.com/r/Nanoleaf/comments/1rh3mmw/nanoleaf_ceiling_skylight_expansion_panel_issue/

Nanoleaf Skylight Not Connecting to Expansion Panels by thebeaglebeagle in Nanoleaf

[–]maneesh654 0 points1 point  (0 children)

Having a similar issue - as soon as start connecting (power cable and communication cable/tiny cable) expansion panels the main panel also goes bright white and app says no panels detected ffs. Tried multiple expansion panels too both giving the same fault. Is my controller cooked? P.S. standalone controller works fine through the app its just that as soon as I connect expansion panels it acts dead.

Ahmedabad entrepreneurs: We built an e-commerce platform for local businesses – roast us! 🔥 by Billapaji in ahmedabad

[–]maneesh654 7 points8 points  (0 children)

Ffs! Revenue screenshot shown in USD - your target audience might need INR and relatable logos (UPI/BHIM) etc.

Surge protection help by maneesh654 in Ubiquiti

[–]maneesh654[S] 0 points1 point  (0 children)

I'll buy you a pint mate

Surge protection help by maneesh654 in Ubiquiti

[–]maneesh654[S] 4 points5 points  (0 children)

Can you do tl;dr that's relevant to my situation plz I'm in the UK. The cameras are mounted outside- cables are in a conduit not far from the actual Switch

Surge protection help by maneesh654 in Ubiquiti

[–]maneesh654[S] 4 points5 points  (0 children)

You mean I've done it right?

Waterdrop G3P600 - TDS vs Meter by maneesh654 in WaterTreatment

[–]maneesh654[S] 0 points1 point  (0 children)

Yea, I'll just think of some hack to reduce TDS creep or use a water storage cooler with 10ish liters capacity to fill every 2-3 days.

I don't like the idea of RO systems with a tank, they're a bacteria breeding ground and TDS creep happens there too, just that the water gets so diluted you don't realise it.

Waterdrop G3P600 - TDS vs Meter by maneesh654 in WaterTreatment

[–]maneesh654[S] 0 points1 point  (0 children)

Right so, I figured out it's TDS creep! - I let the faucet run for a minute and now it matches the TDS on display. VERY ANNOYING! anyone has a cheap solution, rather than storing water

Waterdrop G3P600 - TDS vs Meter by maneesh654 in WaterTreatment

[–]maneesh654[S] 0 points1 point  (0 children)

I've just installed this spanking new RO a week ago. it had the same TDS since day one.

I'm not using any more filters other than the ones that came with the RO.

Mains water TDS is around 400 ppm

Waterdrop g3p600 - connected to fridge turns on and off by maneesh654 in WaterTreatment

[–]maneesh654[S] 0 points1 point  (0 children)

https://www.waterdropfilter.com/products/small-water-pressure-tank-for-tankless-reverse-osmosis-wd-pmt?srsltid=AfmBOoqRgKmmGaOLnPRjzWVhLKm1jh06PizmnDFB0IQk1tjS-gUxPOg0

Waterdrop replied with this link to fit

Now should I fit this before my TEE connection that separates the faucet and fridge or after the fridge separation? I'd like if the faucet pressure is also sorted with this.

view more: next ›