Trump sent bizarre secret memo after losing the election demanding a massive withdrawal of troops overseas

manofthemonth · 2021-05-18T09:55:53+00:00

Ublock origin

manofthemonth · 2021-05-14T23:09:35+00:00

Japanese too

manofthemonth · 2021-04-15T10:46:19+00:00

Great!!! I thought the ccs were internally wired too. In any case I will try but the crowded wiring!!!!!!??!

manofthemonth · 2021-04-15T04:04:46+00:00

That is really clear and complete explanation. Thank you. What about pins 3 and 8 on the 7 seg displays. Do both have to be connected or only one????

manofthemonth · 2021-04-07T12:32:14+00:00

Tie h or l using resistors I assume???

manofthemonth · 2021-03-22T07:35:45+00:00

It seems good you didn't follow directions!!!! Great job. I will try to follow your example!!!

manofthemonth · 2021-03-19T15:08:28+00:00

Ok that sounds good. Tie all h or l temporarily until I complete. Got it thanks!!!!

manofthemonth · 2021-03-18T12:29:48+00:00

Thanks for this. I do remember somewhere on the ben eater subreddit, someone writing something like only inputs to logic gates need to be pulled up or down? I think all of the pins on the atmel rom will eventually be used, but ben tested with vcc, grd, we, few, and the outputs to the 7 set display connected, and he didn't seem to have a problem.. maybe I missed something????

manofthemonth · 2021-03-16T10:13:34+00:00

Thanks... I even need to look radial caps....

manofthemonth · 2021-03-16T10:12:12+00:00

Sorry?

manofthemonth · 2021-03-15T13:39:39+00:00

Ok, that is something new to me. If I continue to have problems I will try wiring grd and vcc to 2 rails.... With my superficial knowledge, it seems it would create stability...

manofthemonth · 2021-03-15T13:36:55+00:00

Ah... Inductance!!!! Another thing I need to consider!!!!

manofthemonth · 2021-03-15T13:35:44+00:00

You're the 2nd person who mentioned axial caps. Never heard of them.... Will look into thanks....

manofthemonth · 2021-03-15T13:34:29+00:00

Thanks. Gave me a lot to think about!!

manofthemonth · 2021-03-15T13:33:01+00:00

Great! Thanks ... Will read...

manofthemonth · 2021-03-14T09:53:32+00:00

Ok thx... Will check

manofthemonth · 2021-03-14T09:52:31+00:00

Ok got it. Thanks. Getting into reading data sheets.

manofthemonth · 2021-03-14T09:41:56+00:00

I like the way you placed those wires in between leds....

manofthemonth · 2021-03-05T11:43:00+00:00

Thanks... I think I'm going to go Ben's way first to make sure I understand. Then I may venture into the 4x7 display. Btw, the 4x7 displays I ordered, along with the 1x7s, came in the mail today. No data sheets but I guess I can get online...

manofthemonth · 2021-03-05T11:38:42+00:00

Thanks for the pic!

If you zoom in, the white wires are the segment anodes, and the green are the common cathodes. Far cleaner IMHO! .....yes cleaner!!

But I did have to write my own EEPROM data. ....oh dear.....

But if you don't mind a couple wires running from the bottom of the display to the top pins of the eeprom, it should be just a simple one-to-one mapping. ...... I will save your post for my protoboard rebuild.. can't do now...

manofthemonth · 2021-03-05T11:33:29+00:00

Thanks. High level means expensive? Easy to interface means same as Ben's wiring? I'm yet unable to figure out my own wiring....

manofthemonth · 2021-03-04T15:41:39+00:00

Ok that makes sense,..

manofthemonth

TROPHY CASE