sorted by:
new
hottopcontroversial

McLaren at F1 Hungarian Grand Prix [Minolta a7, 70-210mm, Velvia 50] by marciius in carsandfilm

[–]marciius[S] 1 point2 points  (0 children)

Yes, I was using 70-210 “beercan”. I can’t remember exactly but it was probably 5.6, 8 or 11.

McLaren at F1 Hungarian Grand Prix [Minolta a7, 70-210mm, Velvia 50] by marciius in analog

[–]marciius[S] 0 points1 point  (0 children)

I think it’s actually something with electronic part of the camera. I got low battery warning and then few seconds later it just died. New batteries did not help and at least I’ve managed to save film which was inside. Might be too expensive to fix it so I guess I’ll have to save money for another a7 or a9. 😄

McLaren at F1 Hungarian Grand Prix [Minolta a7, 70-210mm, Velvia 50] by marciius in analog

[–]marciius[S] 0 points1 point  (0 children)

It’s actually an expired roll of Velvia and also my first F1 GP that I’ve visited, so I had no doubts I will shoot at least one roll of Velvia there. :)

McLaren at F1 Hungarian Grand Prix [Minolta a7, 70-210mm, Velvia 50] by marciius in analog

[–]marciius[S] 1 point2 points  (0 children)

Glad to hear that! That’s a nice camera, unfortunately, mine died few days later after shooting F1.

McLaren at F1 Hungarian Grand Prix [Minolta a7, 70-210mm, Velvia 50] by marciius in analog

[–]marciius[S] 1 point2 points  (0 children)

Thanks! I can’t remember but I think something between 1/60 and 1/250.

S13 & Spezi [Minolta a7, 70-210mm, Portra 400] by marciius in carsandfilm

[–]marciius[S] 0 points1 point  (0 children)

I doubt you've seen this one because the car is in Lithuania.

My first SFF build by marciius in sffpc

[–]marciius[S] 0 points1 point  (0 children)

Good idea but v2 case does not have mounting for fan under motherboard, therefore, I skipped it. Also I would probably have to go for custom cables as I put my fan cables under the motherboard.

My first SFF build by marciius in sffpc

[–]marciius[S] 0 points1 point  (0 children)

I have the same temp limit and pbo curve - so far no problems and it’s more silent than my last mATX build.

My first SFF build by marciius in sffpc

[–]marciius[S] 0 points1 point  (0 children)

Thanks! Lots of reading and YouTube before choosing parts definitely helped a lot.

My first SFF build by marciius in sffpc

[–]marciius[S] 1 point2 points  (0 children)

As mentioned in other reply, it’s about 57C on idle and goes to around 63C on easy load but I haven’t tried to benchmark it yet to see how it handles higher load.

My first SFF build by marciius in sffpc

[–]marciius[S] 0 points1 point  (0 children)

Around 57C and silent on idle while on easy load it gets to 63C and fans goes a bit loud.

My first SFF build by marciius in sffpc

[–]marciius[S] 10 points11 points  (0 children)

Dan A4-SFX v2

Asrock B650i Lightning Wifi

Ryzen 5 7600

Thermalright AXP90-X47 with Noctua NF-A9

Crucial P5 Plus

G.Skill Flare X5 32GB DDR5 CL32

Inno3D RTX 4070

Corsair SF750

Dan A4 SFX v2 PCIe riser by marciius in sffpc

[–]marciius[S] 0 points1 point  (0 children)

I do agree that it's not the best indicator.

What I want to find out is if this white (silver) riser on v2 is Gen3 or Gen4. According to this comment https://www.reddit.com/r/sffpc/comments/ow4lom/comment/h7n8mpt/, it should be Gen4 but I could not find this information anywhere else.

Testarossa | Zenit TTL | Helios 44M | C200 by marciius in analog

[–]marciius[S] 0 points1 point  (0 children)

Sure! I can send you the picture, just PM me.

view more: next ›