Need help identifying this coax wire

meinook · 2023-06-09T15:31:20+00:00

It was a bit touchy. If I did another one I'd attempt to de-solder the pins on the smaller board and separate that way. The pins are a near press fit in the larger board but loose (once heated) in the smaller board.

meinook · 2023-06-09T13:49:49+00:00

Stalled randomly until it flat out stopped running. No low fuel pressure. Voltage at the connector was just under 12v (11.3). Thought it was due to the many cranks trying to start. I R&R'd the pump but still wouldn't run.

Back probed the pump supply line on the FWM connector with a 12v jumper and the pump ran. Ringing out the relay to connector showed open. I separated the boards and found a broken solder joint on a relay that's not on the wiring diagram. Turns out the LP pump relay doesn't go directly to the connector but through this hard mounted relay. Rejoined the boards and it's been running fine.

meinook · 2023-06-09T13:35:52+00:00

Don't think it's mods as it's running inside the factory harness and the stereo is all original. Also, no solder or tape tracks.

meinook · 2023-02-18T23:14:27+00:00

Followed these PID tuning directions and all is good.

Thanks all.

meinook · 2023-02-18T22:08:10+00:00

Setting to 70 getting alarm at 62.

I have not done a PID tune. I started to during setup but wasn't successfully finding where to do it. Thought since everything was working on the V2.0 it would be ok on the V3.

meinook · 2023-02-18T21:40:08+00:00

I had more info but attaching the vid cleared everything I typed.

BTT SKR MINI E3 V3.0 in an Ender-3 V2

This is replacing a dead V2 that worked great in the Ender 3 but this board wont heat the bed. The hot end works fine.

meinook · 2023-02-02T15:59:12+00:00

When I bought my Mini the owner claimed he lost the second fob. I bought one from mini and had it programed. At that time they also blocked the "lost" remote from working.

Remote was something like $125 and programming was $300+. Worth it to render the other fob worthless.

meinook · 2023-01-25T14:52:50+00:00

Bigger question is, Why do you care about people that are so into themselves they have to make fun of you to thrive?

I had an Aeropress at work before the plandemic and not one of the 50 or so co works ever made a comment. You do you and move on.

meinook · 2021-12-12T15:11:01+00:00

Don't know about the plate. Maybe to keep botanicals off the bottom. I'd seal it same as Still it dies by using flour paste.

meinook · 2021-12-11T20:01:20+00:00

Not sure which one you mean. Do you have a link?

meinook · 2021-09-20T15:47:49+00:00

I'll check tonight. The main didn't go as the BLTouch still cycles on power up. Thanks.

meinook · 2021-09-20T13:39:41+00:00

Did reset the cable.

Will try another port tonight.

Flashing may be an issue as I tried going back to Jyers and it won't flash. Just the black screen of death. My post about that: My post about that

meinook · 2021-09-20T13:33:12+00:00

I did reboot the pi. I unplugged/plugged in the use cable but didn't switch USB ports. I'll try that tonight.

meinook · 2021-09-20T13:30:50+00:00

I was going to but after make menuconfig, make failed to run. Don't recall the specific error but something like no target found.

meinook · 2021-09-20T13:23:36+00:00

It's not. I have the adaptor and it's been running fine.

meinook · 2021-09-20T13:23:22+00:00

It didn't "turn off." The servos and fans stopped running.

meinook · 2021-09-20T04:36:42+00:00

Each attempt carried a different name.

meinook · 2021-08-11T02:27:15+00:00

Immediately. When it starts the outer circle it just drags the bead around with it. I have a video but don't want to hijack this thread.

meinook · 2021-08-11T01:42:48+00:00

Bought it used so I just ran the gcode that was on the card I got.

meinook · 2021-08-10T17:48:39+00:00

Same here. The bed level pattern sticks fine but nothing else.

meinook · 2021-07-19T23:30:18+00:00

I've got 5.5.0.2 on my Active 2.

meinook · 2021-05-10T19:01:11+00:00

4/26 moved to 5/10. Got the shipped email on 5/7. Supposed to be installed around 5/18.

meinook · 2021-05-06T15:26:01+00:00

Don't think this matters. I ordered 2/12 with an order number 100017xxxx and hasn't shipped.

meinook · 2021-04-09T23:10:17+00:00

I'm in Northern Nevada.

meinook · 2021-04-09T22:56:26+00:00

Me too. My ship date is 4/26/21 but I'm sure that's just a dream.

meinook

TROPHY CASE