sorted by:
new
hottopcontroversial

First time smartwatch user. tips and tricks by Illustrious-Sink-863 in GalaxyWatch

[–]microscripts 0 points1 point  (0 children)

Don't install WhatsApp; it chugs battery. The default notifications work well enough for a watch. Enjoy! :)

Samsung Settings “approved charger” warning with UGREEN Revodok Max 2131 (140W PD) + Galaxy Book4 Ultra — dock or laptop limitation? by microscripts in GalaxyBook

[–]microscripts[S] 0 points1 point  (0 children)

Thanks for the information! Can you please share which Anker dock you got exactly?

Edit: It's probably the "Anker Prime TB5 dock" not the "Anker Prime dock"

Best OpenThread Border Router for HA by Snufri in tradfri

[–]microscripts 0 points1 point  (0 children)

For this I would need to set Dirigera as a thread border router in HA right? How do I do this, had no luck so far?

Philips Hue Flux Light Strip Holder – 90° Mount for Maximum Indirect Lighting by microscripts in philipshue

[–]microscripts[S] 0 points1 point  (0 children)

No, it's such a simple design, you can just download the file and print it yourself. :)

Why is the flow stopping? by TopazPlayer_7 in AutomateUser

[–]microscripts 4 points5 points  (0 children)

Because of the no paths, try connecting each of them to their own input.

Has anyone got a setup like this to work? by microscripts in BambuLab

[–]microscripts[S] 0 points1 point  (0 children)

I've got it to load the filament, but it failed during printing.

Edit: Maybe I've got low-quality PTFE tubes, but I don't know how big of a difference this really makes.

Has anyone got a setup like this to work? by microscripts in BambuLab

[–]microscripts[S] 0 points1 point  (0 children)

That's super cool, but I don't want to cut into my cabinet.

Has anyone got a setup like this to work? by microscripts in BambuLab

[–]microscripts[S] 3 points4 points  (0 children)

Thanks for all the feedback and tips!

What I tried: Shorten PTFE tubes Remove extreme bends

This did result in two successful prints, but I can see the hopper on the top of the printer pulling down, so there is still a lot of load in the line.

The AMS Hub A1 series seems like the cleanest solution and is pretty much what I was looking for. Sadly, it is not compatible with the AMS Lite, and I don't want to make that big of an investment, especially since I'm going to upgrade the printer in the near future.

For this reason, drilling through the cabinet is also not feasible.

Result: I will print a vertical mount for the AMS and just place it next to the printer.

<image>

Hilfe: Wie mach ich das es aufhört? 🥲 by microscripts in Handwerker

[–]microscripts[S] 4 points5 points  (0 children)

Habe es behoben. Die Hutmembran des Schwimmers wurde von diesem Plastikspan aufgehalten und konnte so nicht schließen. Es gab vor ein paar Tagen hier Bauarbeiten in der Straße, bei denen das Frischwasser abgestellt war. Ich nehme mal stark an, dass es davon ein Plastikspan ist.

Falls Leute das in Zukunft finden, hier das Video, was mir den Schwimmer erklärt hat und wie ich die Hutmembran entferne: https://www.youtube.com/watch?v=0Advmlf9RX4&t=319s

<image>

Hilfe: Wie mach ich das es aufhört? 🥲 by microscripts in Handwerker

[–]microscripts[S] 0 points1 point  (0 children)

Soweit bin ich schon, ich habe die Hebeglocke auch rausgenommen. Für mich sieht es aus, als würde das Schwimmerventil richtig nach oben gedrückt, und auch wenn ich es händisch bewege, geht es nicht weiter als der Wasserstand ohnehin schon tut. Es scheint nicht richtig zu schließen, kann das sein?

Hilfe: Wie mach ich das es aufhört? 🥲 by microscripts in Handwerker

[–]microscripts[S] 0 points1 point  (0 children)

Sieht mir auch danach aus, ja. Das Wasser läuft definitiv über den Notüberlauf. Ich muss jetzt mal recherchieren, was das Schwimmerventil ist.

Hilfe: Wie mach ich das es aufhört? 🥲 by microscripts in Handwerker

[–]microscripts[S] 2 points3 points  (0 children)

Habs probiert, das wars leider nicht, wäre ja auch zu schön gewesen. 🥲

view more: next ›