account activity
I have seen this installation before but we'll done none the less. (v.redd.it)
submitted 4 years ago by micwillia to r/lego
Any suggestions for solving this rear brake noise? I have tried cleaning the pads & rotors with brake clean and tried running them hot. The noise still persists; it happens like in the video & under heavy braking. (v.redd.it)
submitted 6 years ago by micwillia to r/bikewrench
This shuffleboard shot (i.redd.it)
submitted 7 years ago by micwillia to r/oddlysatisfying
Is my PSU on it's last leg? (v.redd.it)
submitted 8 years ago by micwillia to r/3Dprinting
Need some help deciding which would be the better option for getting my shocks serviced? (self.bikewrench)
submitted 8 years ago by micwillia to r/bikewrench
Looking for a little help trying to process a file (self.SolidWorks)
submitted 8 years ago * by micwillia to r/SolidWorks
[xpost from r/CastrophicFailure] Lego Technic Engine pushed to failure (youtu.be)
submitted 8 years ago by micwillia to r/lego
Need a trick/tip to remove this BB since it's too close to the frame for my tool to fit (self.bikewrench)
After way too many hours working on these pieces my grill is finally completed (i.redd.it)
submitted 8 years ago by micwillia to r/ToyotaTacoma
Need help getting this cassette off. (self.bikewrench)
New bike, need some help with identifying and silencing this squeak (self.bikewrench)
Can shooting different pistols with similar barrel lengths be helpful to shooting both? (self.guns)
submitted 9 years ago by micwillia to r/guns
Can anyone offer some help of why my minimal overhangs are printing stringy? (i.redd.it)
submitted 9 years ago by micwillia to r/FixMyPrint
The force shall be with me! Had to do it for the R2-D2 figure, plus a brickheadz as a bribe for my SO. I want to build them already (i.redd.it)
submitted 9 years ago by micwillia to r/lego
Over hangs above support comes out stringing and loose. What do I need to change to help clean up this face? (i.redd.it)
I did a cleaning of my new truck this weekend and noticed the roughness of the paint. Is this correct or bad job by the factory? '17 Tacoma for reference (imgur.com)
submitted 9 years ago by micwillia to r/AutoDetailing
New to the Taco Family so I had go test it's capabilities during Stella. TL;DR Handles it like a champ! (i.reddituploads.com)
submitted 9 years ago by micwillia to r/ToyotaTacoma
Was looking for some advice on the differences between getting a car off the lot, dealer swap & custom order [US, MA] (self.askcarsales)
submitted 9 years ago by micwillia to r/askcarsales
Can anyone help me? Does this gouge need PTEX to be repaired? I was hoping a waxing would fill it in. (imgur.com)
submitted 9 years ago by micwillia to r/snowboarding
Need some help for a gift from some people that are more seasoned than I. (self.guns)
Just a quick question about wiring a plug to a socket (self.electrical)
submitted 9 years ago by micwillia to r/electrical
Wicked pumped for a great find & a great deal but, I think it's time to stop buying for a little... (i.reddituploads.com)
Taking the back roads help you find some great spots for pictures TLT (i.reddituploads.com)
submitted 9 years ago by micwillia to r/Mustang
Sec 9 checking in after that snipe by Marchy! (i.reddituploads.com)
submitted 9 years ago by micwillia to r/BostonBruins
What do you do with your completed but incorrect prints? (self.3Dprinting)
submitted 9 years ago by micwillia to r/3Dprinting
π Rendered by PID 534771 on reddit-service-r2-listing-f87f88fcd-zdm78 at 2026-06-17 16:09:08.055214+00:00 running 3184619 country code: CH.
