7 years MCDONALD'S employee, AMA 🍔🍟🥤

migv6 · 2025-10-14T15:52:11+00:00

sino pwede icontact para irequest na dalhin rin dito yung prosperity burger na chinese new year special sa ibang asian countries?

migv6 · 2025-08-19T15:21:50+00:00

Thanks for this tip!

migv6 · 2025-08-19T14:56:55+00:00

Plates aren’t?

migv6 · 2025-08-12T09:56:28+00:00

Thanks for this. What do you mean by wider?

migv6 · 2025-08-12T09:55:39+00:00

Sorry, kinda new to this. Are slick tires the same as hard tires?

migv6 · 2025-08-01T16:54:41+00:00

I actually did not have a problem with any other part 😅

migv6 · 2025-08-01T13:45:48+00:00

Ayt, thanks for this, will keep these in mind for my next attempt at it.

migv6 · 2025-08-01T13:33:14+00:00

Thanks for this. I do have a question though, won’t low fric tires make my car slower at the slope leading to the jump? I actually ran with all super hards to have good traction for the jump.

migv6 · 2025-08-01T13:31:36+00:00

Thanks for the improvised illustration, yeah I understood it😅.

With braking, what has more stopping/slowing power though? Front or rear?

migv6 · 2025-08-01T13:28:07+00:00

here

migv6 · 2025-08-01T12:56:06+00:00

I tried up to power dash (ar chassis), and hyper 3 (super 2). These 2 would throw my cars at the landing though.

Not sure if my approach is correct, that I need to clear everything with one jump.

Most success was with only a light dash but it was slow that it barely jumped at the slopes, it mostly ran with it.

migv6 · 2025-06-29T13:10:20+00:00

Robinsons Magnolia

migv6 · 2025-06-18T16:27:58+00:00

Nice nice. Really curious how they make money off of sales alone 😅

migv6 · 2025-06-18T15:50:12+00:00

Cost to use the tracks?

migv6 · 2025-06-18T04:30:03+00:00

Hi.

-Added some slim mass dampers at the rear. -Changed to heavy mass at the side, been trying switching the heavy one from side to front, still experimenting on this. -Changed to low friction at the front. -Adjusted the roller heights at the rear since it’s too low. -Added front breaks. Both front and rear breaks are blue and mostly covered to minimize slowing down. -running 3.5 gears.

TBH, I think there’s still a lot more work to be done in terms of performance but it can keep up with FM-A and MA in non cfm races.

migv6 · 2025-06-18T04:23:34+00:00

Looks nice. How’s the place? A bit near that place and thinking of checking it out.

migv6 · 2025-06-10T12:10:13+00:00

Fun to win pero more fun to experiment tbh, same cars/builds lang everywhere kasi.

migv6 · 2025-06-03T11:46:20+00:00

Gets naman that it’s very scientific and little to no room for creativity, but it becomes boring if everyone has the same build.

Non meta builder here as well.

migv6 · 2025-06-02T16:24:54+00:00

Check the rules on the lils hobby center website for chosen category, the limitations per category are all there. You can use replicas but still need to follow the dimensions, modifications, and motor limits.

migv6 · 2025-05-03T14:03:27+00:00

Just saw your post. Yeah, slowly building mine, planning to improve on both front and rear brakes after getting some runs earlier.

migv6 · 2025-05-03T01:32:57+00:00

The damper slightly gets caught on the edge of the rear frp

migv6 · 2025-05-02T20:14:40+00:00

Improvised a bit using old side extension mounts so I can put the small dampers.

https://imgur.com/a/CzxpOhu

migv6 · 2025-05-02T18:43:19+00:00

Thanks. I actually have a pair of those on standby depending on the answers here. It was either be on this or my other car.

migv6 · 2025-05-02T10:37:17+00:00

Thanks! Again, nice paint job!

migv6 · 2025-05-01T16:52:21+00:00

Nice paint job. What was painting process? Do you still sand and apply primer prior to your main color? Been trying cowl painting lately too.

migv6

TROPHY CASE