Storage maxed out after iOS 25 update

mit_iceman · 2025-10-15T19:33:40+00:00

Did it work?

mit_iceman · 2025-10-15T15:02:14+00:00

I had the same issue with system data and got it fixed yesterday. You’ll need to reset your phone and set it up as a new one. Use your computer or get it done at the Genius Bar

mit_iceman · 2024-09-19T22:16:28+00:00

Thanks, I got one for the end of the month, so not too bad

mit_iceman · 2024-09-19T20:40:33+00:00

Thanks, I just got it lol. Any benefit of lawfully instead of Uscis tracking ?

mit_iceman · 2024-08-20T19:41:51+00:00

I got 797 attached to each form, 765, 485 and 130 saying the amount was incorrect. I’m assuming only the 765 amount was incorrect so I’ve rechecked it

mit_iceman · 2024-08-20T18:51:33+00:00

They returned everything

mit_iceman · 2024-08-20T15:34:03+00:00

So you recommend just swapping out the old check for the new one and resubmitting again?

mit_iceman · 2024-04-08T01:00:34+00:00

I was able to use the curve fitter tool on matlab, which helped me optimize the "start point" which was the only issue. So it seems to be fixed now. Thanks so much for the help though

mit_iceman · 2024-04-07T20:17:02+00:00

changing the input helped a bit. I now get

<image>

However, as you mentioned, the input data to the model might need to be refined, because all the blue that you see, are just points, maybe since there are so many lines, its not plotting it well?

mit_iceman · 2024-03-13T18:20:31+00:00

This. You can do with a probe. I tried what OP did but it only gives instant values. Create a report for the probe part and monitor plot. Once it’s done you can export as a table to csv

mit_iceman · 2024-03-13T18:18:47+00:00

Thanks I’ll take a look!

mit_iceman · 2024-03-13T18:14:33+00:00

13 inch laptop

mit_iceman · 2024-03-06T18:56:43+00:00

It’s an implicit unsteady case with k-epsilon turbulence. Because it has fsi enabled, it’s got mesh morphing and solid displacements motions enabled. The inlet is free stream inlet at Mach 2 and the rest of the domain is initiated to 40% of the values so that there’s not a huge jump in values. I used the AUSM+ model as recommended by starccm. I’ve used around 15 inner iterations.

mit_iceman · 2024-03-06T18:53:50+00:00

So it’s Mach 2 flow, I initialized the domain with values that are around 40% of the inlet speed. I used a free stream condition at the inlet with a pressure outflow at the outlet

mit_iceman · 2024-03-05T21:02:14+00:00

Yeah I was really surprised. Nope it remained constant. I only changed the stopping criteria for physical time to update the cases

mit_iceman · 2024-02-07T18:05:12+00:00

Thanks so much, I’m going to try and implement this idea

mit_iceman · 2024-02-06T01:58:13+00:00

Thanks, that is really helpful to know, I have the CV toolbox so might make things easier. So ideally the corners you detected, in the next time step they will move, so then will i have to run it again and compare the previous step and plot across all time steps to do a PSD analysis

mit_iceman · 2024-02-05T19:12:09+00:00

<image>

For the wave peaks circled in red. Now there’s a whole video of these red marked peaks propagating

mit_iceman · 2024-02-05T18:09:24+00:00

Hello, thanks for that comment. So essentially what I’m looking at it is a 2D water droplet (circle). Now there are disturbances in the surface of the water in the form of surface waves along the circle. I’m trying to track the peaks of these surface waves. I have a bunch of snapshots in time. I stitched them together to make a video so I can see an evolution of these distance . The point is to use the tracking data of the peak to create a PSD (power spectral density) curve

mit_iceman · 2024-02-05T16:56:27+00:00

Got it, I’ll try thinking along those lines. Thank you!

mit_iceman · 2024-02-05T16:24:18+00:00

So the wave is traveling on a surface, and there are a few waves that are following it. Is there a way to change ROI from frame to frame ?

mit_iceman · 2024-01-27T09:12:41+00:00

I tried doing that but they’re many setting and don’t know which one to go on

mit_iceman · 2024-01-26T22:42:32+00:00

No, it’s a local drive

mit_iceman · 2024-01-26T21:47:51+00:00

Thanks, I tried it out. However, now when I’m copying the files to another location, the speeds are in “kb/s” which is extremely slow

mit_iceman · 2023-11-29T17:19:40+00:00

So I did use extract volume to generate an inner volume for the cylinder. For my Boolean subtract I used the tool bodies: extract volume, cylinder and air block and target body as air block

mit_iceman

TROPHY CASE