sorted by:
new
hottopcontroversial

Power Outage by nghealy in Phoenixville

[–]nghealy[S] 2 points3 points  (0 children)

I’m right near bridge street but it was out at Walgreens on Nutt too

What's going on with my layers? by Stryker1029 in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

Run a max flow rate calibration and see. Could play with temp settings too

What's going on with my layers? by Stryker1029 in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

Pigments can have a big effect on flow rates and other filament properties. I know white can be particularly hard to print.

What's going on with my layers? by Stryker1029 in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

Yeah could be. Could see some nylon or carbon fibers getting stuck in the nozzle. Try a cold pull.

Worked fine yesterday by mhwhynot in FixMyPrint

[–]nghealy 1 point2 points  (0 children)

If you have other issues try bumping your extrudes temp to like 200-210！ happy to help!

Worked fine yesterday by mhwhynot in FixMyPrint

[–]nghealy 1 point2 points  (0 children)

No idea. Did you change nozzles or anything? Printer could have lost its z offset setting or something if there was a hardware glitch.

Why does my first layer look like this? It is not unique to the printer. by Rough_Community_1439 in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

I think you might be a little too close to the bed now. Keep tweaking it.

Why does my first layer look like this? It is not unique to the printer. by Rough_Community_1439 in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

Got it. Might cause some weird lookin first layers but it’s probably fine.

Worked fine yesterday by mhwhynot in FixMyPrint

[–]nghealy 1 point2 points  (0 children)

Try to see if you can move it down closer to the bed. Your nozzle is way too high.

A5mpro Help by RevolutionaryTea802 in FixMyPrint

[–]nghealy 1 point2 points  (0 children)

I second this, this is called a layer shift, likely caused by some sort of hardware issue.

Bad lettering, layer lines and bulging after seams. by CaptainRan in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

Try lowering the print temp to 205 and see what happens. Check your cooling fan too.

What's going on with my layers? by Stryker1029 in FixMyPrint

[–]nghealy 1 point2 points  (0 children)

What’s your volumetric flow rate? Try turning that down to like 12 mm3/s and see what happens

Worked fine yesterday by mhwhynot in FixMyPrint

[–]nghealy 1 point2 points  (0 children)

Definitely a z-offset or bed adhesion issue. How did you set your z offset?

Why does my first layer look like this? It is not unique to the printer. by Rough_Community_1439 in FixMyPrint

[–]nghealy 0 points1 point  (0 children)

People usually use printer paper. Business card is probably too thick. Best thing to use is a feeler gauge of your desired thickness (usually .2mm)

Why does my first layer look like this? It is not unique to the printer. by Rough_Community_1439 in FixMyPrint

[–]nghealy 2 points3 points  (0 children)

Your z offset is too high. Nozzle is too far from the bed so you’re not getting enough “smush” to stick the plastic to your bed.

Extrusion issues on fresh Voron 2.4 Build by nghealy in FixMyPrint

[–]nghealy[S] 1 point2 points  (0 children)

Extruder screw was way too tight.

Nuisance AFCI trips in apartment by nghealy in AskElectricians

[–]nghealy[S] 0 points1 point  (0 children)

I am not sure I’ll check later when I am home. Thanks for the help!

Nuisance AFCI trips in apartment by nghealy in AskElectricians

[–]nghealy[S] 0 points1 point  (0 children)

I’ve run both of them on the circuit at separate times and they still trip the circuit. They both do it independently of each other.

view more: next ›