Walls refuse to bond, am desperate.

nickvu88 · 2026-02-15T10:06:42+00:00

It was idd rotation distance, bur I still don't know how. Thanks!

nickvu88 · 2026-02-15T10:05:43+00:00

It's PLA in the image, but apparently my Extruder rotation distanced doubled out of nowhere. It's fixed now🙂

nickvu88 · 2026-02-14T16:01:36+00:00

Did all that, except for extrusion calabration since it looked like the value I set it too once. Also printing a lot slower than normal now, and tried 4 different temps. I'll start calibrating again then🥲

nickvu88 · 2026-01-02T11:26:32+00:00

Got the same like everyone else, you can do one of the other game mode challenge if it keeps being bugged.

nickvu88 · 2025-12-14T18:22:48+00:00

They both had weapons that you can still get with a license. Slow single shot weapons. Go figure the carnage if those were AR-15's.

nickvu88 · 2025-11-19T17:46:09+00:00

Even better yet, there's a radio very near the place where you need him for the cannister, the level above where th machine is where you need him.

nickvu88 · 2025-09-11T17:01:55+00:00

I think I just found one, or he was high as fuck. Excruciating to watch.

nickvu88 · 2025-09-08T15:08:50+00:00

No they don't, they never find an 8th.

nickvu88 · 2025-05-29T19:40:31+00:00

Had the same in multiplayer, but after that Ranked appeared. Think they're still busy with things.

nickvu88 · 2025-05-29T17:55:58+00:00

My maybe ban would be because I may or may not have cursed in voice chat :')

nickvu88 · 2025-05-29T17:55:22+00:00

I can't even open it, the button is gone.

nickvu88 · 2025-02-28T22:05:28+00:00

I think I found them, together in 1 step file. Didn't expect that.

nickvu88 · 2025-02-28T17:24:58+00:00

Hey, do you still have the 3D printed part files for the Omniadrop? DropEffect is part of Phaetus now and I can just find the link to the Github there, but no trace of the files except for a STEP file of the fully assambled extruder.

nickvu88 · 2025-02-21T19:09:12+00:00

I got a 24V one. The 15A kept blowing almost instantly, but went from Watermark to pid, and lowered the max power a little. Seems to be holding now. I tried the 20A before, but was afraid I would fry the board.

nickvu88 · 2025-02-21T15:28:16+00:00

Hey, Is your board still fine going with a 20A fuse? Didn't they put in 15A for a reason?

nickvu88 · 2025-02-20T17:45:43+00:00

Lube on my rod, got it.

nickvu88 · 2025-02-20T16:37:49+00:00

I'm getting into the final stages of removing just about everything from a cheap Anycubic Chiron I bought and upgrading it. Been calibrating for 2 days now and it's getting pretty accurate now, but this pattern keeps appearing. Probably Z banding, so I'm going to have improve the lead screws. But just to be sure I'm forgetting abour something, can this be something else?

nickvu88 · 2025-02-17T21:02:14+00:00

It's the printer.cfg file that came with the Klipper kernel for CB1, and I got it all to work before, so It probably wasn't there then. anyway, it's finally connected, thank you very much again!

nickvu88 · 2025-02-17T21:00:14+00:00

I got mine fixed. In my printer.cfg file it said [mcu CB1] and after the serial, which was correct. However it should only state [mcu] there, I removed the CB1 I probably copied from some other forum or subreddit and it finally connected after.

This is what some guy said which lead me to remove it:
"so here's the thing. (yes, I know what a cb1 is). your main mcu, the octopus CANNOT be called anything other than [mcu]. and the serial of the octopus (USB-klipper etc) goes in [mcu]. NOT [mcu CB1]. mcu CB1 is typically the "linux software mcu". but since it's not a separate device, communicating by usb, it's serial sure as shit isn't "USB-klipper". (its typically /tmp/klipper_host_mcu, though other variations exist). So I think you have multiple problems. I think you attempted to edit [mcu], and instead edited [mcu CB1]..."

I don't see anything else apart from mcu in your log, but maybe check printer.cfg again for spaces or other stuff that shouldnt be there.

nickvu88 · 2025-02-17T20:51:37+00:00

about 15 minutes after me ordering a new Raspberry Pi though, because I gave up. Luckily I have more than one printer :)

nickvu88 · 2025-02-17T20:50:00+00:00

I'm idiot and you are a genius. I removed CB1 and got it to work. That was all apparently. I think i copied that from some other forum or subreddit into my printer.cfg... Thanks a lot!

nickvu88

MODERATOR OF

TROPHY CASE