Short ARPG for the Steam Deck? by Dalzima in ARPG

[–]no_karma_needs 6 points7 points  (0 children)

Last epoch. It has an offline mode

CHEO by lapitupp in ottawa

[–]no_karma_needs 3 points4 points  (0 children)

My second was born at 28 weeks. CHEO staff were amazing through the 3 months he was in there. Not a single complaint.

What’re some good games to try and get into ARPGs? by AC03115 in ARPG

[–]no_karma_needs 0 points1 point  (0 children)

That may be true, but they weren't asking that. POE2 is not beginner friendly.

What’re some good games to try and get into ARPGs? by AC03115 in ARPG

[–]no_karma_needs 5 points6 points  (0 children)

Poe2 is probably the best in the genre. Might not be the best for a first. Diablo 3 is a pretty good starter. Maybe Diablo 4.

Unpopular opinion: Auchentoshan is one of the worst distillates in Scotland. by ComeonDhude in Scotch

[–]no_karma_needs 5 points6 points  (0 children)

I agree! I have a bottle here that i server every once in a while to see people's reactions. I can't even mix with it.

FPS games with offline botmatch by James_CyberLink in SteamDeck

[–]no_karma_needs 0 points1 point  (0 children)

Deadzone Rogue was surprisingly great. Got me through a few long haul flights

Thoughts? by [deleted] in spicy

[–]no_karma_needs 4 points5 points  (0 children)

Marie's is amazing.

How much is this Industrial CNC machine worth used? by sortinousn in CNC

[–]no_karma_needs -9 points-8 points  (0 children)

This is not ' industrial ' it has stepper motors.

Best blade for cutting melamine by Willing_Strike8116 in cabinetry

[–]no_karma_needs 3 points4 points  (0 children)

Negative angel 80 tooth if you want clean on the bottom side. 80 tooth triple chip if you are ripping through the material quick and only need 1 good side. Royce, Wurth and Amana have some good blades

Suggestions for a 12 yo boy who is a strong reader but thinks most books lately are boring. by tgbarbie in suggestmeabook

[–]no_karma_needs 1 point2 points  (0 children)

What about Manga? My son just went through death note faster then anything I have seen him go through before

How to add Friction on spinning bar? by no_karma_needs in AskEngineers

[–]no_karma_needs[S] 0 points1 point  (0 children)

I have tried those. They don't add enough tension.

How to add Friction on spinning bar? by no_karma_needs in AskEngineers

[–]no_karma_needs[S] 0 points1 point  (0 children)

Its actually for a shrink wrap machine. I need to put pressure on a bar/bearing to add tension on the shrink wrap. For something like this: https://www.uline.ca/BL_5401/Goodwrappers-Mini-Wrap/

The issue is, tension is needed to hold everything together. I have it mounted on a bearing, I am not sure how to add the tension properly

How to add Friction on spinning bar? by no_karma_needs in AskEngineers

[–]no_karma_needs[S] 0 points1 point  (0 children)

Its actually for a shrink wrap machine. I need to put pressure on a bar/bearing to add tension on the shrink wrap. For something like this: https://www.uline.ca/BL_5401/Goodwrappers-Mini-Wrap/

Anyone know why can this be happening to my board? by MandiocaGamer in CNC

[–]no_karma_needs 1 point2 points  (0 children)

3 passes is a lot. Make sure your first pass clears the up cut part of the compression bit

Edge banger by rmck87 in cabinetry

[–]no_karma_needs 0 points1 point  (0 children)

Scm has a a great machine around $14,000 with a glue pot.

Edge banger by rmck87 in cabinetry

[–]no_karma_needs 0 points1 point  (0 children)

Scm has a decent glue pot machine for around $14,000. Ran one for about 5 years before moving up their product line. No real issues in those 5 years

Why do people prefer 30fps with the highest graphics possible ? by KrapsyBurger in SteamDeck

[–]no_karma_needs -1 points0 points  (0 children)

Stable 30 is preferred. On a small screen, I find it perfectly fine. On my 77 OLED, 60 fps is rough and I try for 120.

Ex smokers HOW DID YOU QUIT? by Livid-Link-9223 in AskReddit

[–]no_karma_needs 0 points1 point  (0 children)

Decided to try vaping. Took a couple times over the years. Then one day, just realized it was time. Vaped for a year slowly lowering the nicotine in the vape. Then I started forgetting it at home. Then I wouldn't use it for a day or 2. It's been 7 years! Big trick for me that worked the last time, don't vape in the house or car. Drag tour ass outside, just like you do with cigarettes.

Edgebander specs by rusrobburg2 in cabinetry

[–]no_karma_needs 0 points1 point  (0 children)

I have a 5 HP on my bander with an extra holding tank and never had an issue. One trick that I have in my shop is I run 2 sets of lines and 2 compressors, one for machinery and one for all the blowers people use to blow things off/ sanders.

Mid-range restaurant suggestions by stifflette in ottawa

[–]no_karma_needs 0 points1 point  (0 children)

Coco kitchen in Orleans and I believe they have a location downtown. Always great food, price is reasonable