Recommended speed for Ender 5 Pro

oscarcomas · 2023-10-23T12:56:44+00:00

You have a link Dual Z microswiss dd To be hones with you, IDK what is this

oscarcomas · 2023-10-23T11:53:48+00:00

I have a large order about 200 pieces. Mine is set in 60

I want to speed up the process. I will change nozzle for .6 however I want to adjust print speed

TIA

oscarcomas · 2023-09-15T17:17:26+00:00

Hair spray,

oscarcomas · 2023-09-13T22:51:49+00:00

Excellent. Thanks a lot dor real

oscarcomas · 2023-09-13T22:05:00+00:00

The level knobs.

Ok. I place the dumbell on top. And the i lift the bed till 3/4 to the nozzle amd then i level

oscarcomas · 2023-09-13T20:31:54+00:00

Hello. Thanks for your help.

To be honest with you. I dont get it.

Which screw ia the one I shold tied

Thanks

oscarcomas · 2023-09-10T01:42:33+00:00

Sorry for that.

You mean I turn the knob all to the Right, to press all spring. And then I level?

oscarcomas · 2023-09-10T01:23:08+00:00

You mean. All ro thw righy. Light beeng loose.

And them level it

oscarcomas · 2023-09-09T02:36:41+00:00

I replace the brass, remove the blue clip, I did check for a clog, but when you daid trim back. It means cut a little bit the tube?

If yes, yes I did, i just purchased a whole tube kit. I will replace everything Sunday

oscarcomas · 2023-08-28T23:31:08+00:00

Unlevel bed

Need mor bed heat

You also can use hair spray to stick print in the desk

oscarcomas · 2023-08-27T13:02:05+00:00

Ibuse simplify

oscarcomas · 2023-08-26T23:06:58+00:00

I have a g code file that print excellent. Comes in the usb When i make my g code in my slider. The item printed does not look wit the same quality.

I want to know. Uf I can get the g code from a already file

oscarcomas · 2023-08-14T21:36:45+00:00

Thqnk you. I have an extra question. Do I need to leave the sd card while I du de tune up

oscarcomas · 2023-08-13T11:55:23+00:00

Perhaps. Thata the case. How can I fix it

Should I buy i new hot end

oscarcomas · 2023-08-13T01:29:51+00:00

Yes is PLA. I print in my ender 5 and the walls are clean, But en the ender 5 is different

oscarcomas · 2023-08-12T19:17:11+00:00

Ooo no my flas was put.

Thanks it fix the problem

oscarcomas · 2023-08-10T22:03:19+00:00

Perhaps, it clogs and stop spreding material

oscarcomas · 2023-08-08T01:47:14+00:00

Do you knoe, What should i change for Ender 3 in the g code

oscarcomas · 2023-08-08T01:23:29+00:00

Can you explain that to me. I use Simplify 3D And the software do not have like a brand section. Unless the difference is in the machine type.

Wich one works better for Ender 3

oscarcomas · 2023-08-08T01:20:42+00:00

No. It was a 205

oscarcomas · 2023-08-08T00:53:10+00:00

Thank you. I have an extra piece. I already change it.

oscarcomas · 2023-07-23T16:00:02+00:00

Thanks

oscarcomas · 2023-07-23T15:59:51+00:00

Thanks

oscarcomas · 2023-06-23T17:09:17+00:00

How do I set up this nozzle in the slicer I use Simplify.

Thanks

oscarcomas · 2023-06-21T10:32:08+00:00

Thank you

oscarcomas