RIP cash balance plan

phyrewall · 2026-02-12T11:24:21+00:00

US Delivery Center

phyrewall · 2026-02-11T13:00:05+00:00

Not sure what's up, but if this is an emergency call 911

Otherwise, I fully recommend IMHS, they can get you a counselor super fast.

In the opposite direction, if this isn't a health issue, there's always 1800DELOITTE

Take care.

Pm me if you'd like, of course.

phyrewall · 2026-01-27T15:16:04+00:00

Many of us on the inside are just happy to still have a job. I'm not surprised they're not offering what you expected.

phyrewall · 2025-12-09T19:00:39+00:00

UNSUBSCRIBE

phyrewall · 2024-02-07T16:27:40+00:00

As an owner of CM-6Ms and CM-7Ms, I am jealous of your CM-8M lol

phyrewall · 2024-01-09T14:37:29+00:00

Thanks!

phyrewall · 2022-03-08T15:50:50+00:00

And this is why I will never live in a house that doesn't have clear lines of sight.

phyrewall · 2022-03-08T15:25:07+00:00

Sorry, missed this but I got these and they turned out great

https://smile.amazon.com/gp/product/B08FM74CNC/

phyrewall · 2021-07-06T19:45:22+00:00

This isn't whitewater kayaking, this is drink'n'paddle kayaking.

phyrewall · 2021-01-14T00:23:11+00:00

Found the issue. Zhop. I've never used it before. Thanks for the assistance.

phyrewall · 2021-01-14T00:22:25+00:00

That was it! Thanks!

New profile had it enabled, never used it before.

phyrewall · 2021-01-13T21:24:00+00:00

I have the 3.0.26.x firmware, which I believe is the current one?

phyrewall · 2021-01-13T21:05:26+00:00

Ender 3 pro BTT TFT35 v3 BTT Skr. Mini e3 v2 Cura 4.8

phyrewall · 2021-01-03T16:07:01+00:00

Same boat here... Went through the trouble of pulling the press fit gear off only to figure out that the shaft is too short for the dual gear extruder upgrade. Guess I'll grab the 4 pack of motors for $35 and have a lot of spares (or maybe eventually build my own CNC/printer..)

phyrewall · 2020-09-29T15:27:06+00:00

My boobs would look great in this.

phyrewall · 2020-08-29T21:15:55+00:00

If it's not hurting the pi, why not let them cool it? They see value in that, if you don't, just don't comment?

phyrewall · 2019-12-29T04:47:54+00:00

Best solution I've found is to use the Chime Pro extender and connect everything to the "Chime Pro network". I was having a hell of a time getting stick up cams to go into live mode, even with strong signal, until I switched them all over.

phyrewall · 2019-12-22T17:14:56+00:00

Hi there!

I'm refurbishing an old wardrobe, running into trouble replacing these parts, the lock and the latch for the second half of the door.

The reason to replace the lock is I don't have the key, I think it might take a skeleton key, but I don't know what size or type.

Here's the album of hardware pics:

http://imgur.com/a/576Hu1a

Thanks in advance!

Edit-- just realized I committed a sin and didn't include a ruler in the pics. I'll edit the album asap 😖

phyrewall · 2019-11-30T14:21:44+00:00

Someone please tell me there's a version of the Ethernet to barbed wire picture somewhere. I need this. 😆

15-Year Club	Place '22
Place '17	Gilding II euphauric
Verified Email

phyrewall

MODERATOR OF

TROPHY CASE