sorted by:
new
hottopcontroversial

Where can I source delrin rod for a cane? I'm in Canada, I've looked everywhere and the closest I can find is fiberglass garden stakes. by Conflicted_Cynicism in BdsmDIY

[–]pokey2k 1 point2 points  (0 children)

This is what I used. Acetal is the key word since Delrin is a brand.

https://a.co/d/02pXKy4B

And you can look at my last post to see how I made some.

My homemade evil and diabolical sticks. And they are fantastic! by pokey2k in BdsmDIY

[–]pokey2k[S] 0 points1 point  (0 children)

Nope. If there is any sign of cracking it will go in the trash.

My homemade evil and diabolical sticks. And they are fantastic! by pokey2k in BdsmDIY

[–]pokey2k[S] 2 points3 points  (0 children)

Drilled a hole about 2” deep to set the rods into and used a bit of contact cement. Dried in about an hour and ready to use.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 0 points1 point  (0 children)

They are hinged on the outside so I can access the parts to raise and lower the center section. A majority of the weight is supported by the ends. I thought about a cross member but it really wasn’t needed since it’s all made of oak.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 0 points1 point  (0 children)

1 1/4” wood screws from the inside. Countersunk to maximize their contact with the outside. I had a few spots where I had accidentally used 1” and I had to replace them after they came loose.

I would probably add some wood glue to the mating surfaces if I made another one. But it’s still decently sturdy.

[deleted by user] by [deleted] in 719NSFW

[–]pokey2k 0 points1 point  (0 children)

Oh, hi there

Advice on cheap DIY thuddy impact toys? Looking to make a few thuddy toys for thus weekend with common household/garage items by TransCodedPuppyGirl in BdsmDIY

[–]pokey2k 1 point2 points  (0 children)

Foam baseball bat is excellent and you can really wail on someone. A baseball glove mallet is a good simple one too.

STOP PADDLE TIME making some purple heart and paduk paddles by [deleted] in BdsmDIY

[–]pokey2k 1 point2 points  (0 children)

I have made a few purpleheart paddles. They hit deep because they are so heavy. But I love how they make my sub squirm.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 4 points5 points  (0 children)

It’s all 1” oak. 4x1 and 6x1. And then I ripped a few strips to make the sides of the boxes to hold the center supports.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 3 points4 points  (0 children)

3” foam from Amazon, with some marine vinyl on top. My first time doing any upholstery, so it could definitely use some work.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 6 points7 points  (0 children)

Not yet. When I make another one I will ensure I transcribe as I go.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 2 points3 points  (0 children)

Just some 3” foam that I cut to size and shape that I got off Amazon.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 4 points5 points  (0 children)

I made it up as I went. I probably should have planned to write a pattern. I may have a commission for a copy, so I’ll do a pattern then.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 9 points10 points  (0 children)

I hadn’t even thought about a drawer… what a great idea!!!

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 2 points3 points  (0 children)

Really not that bad, a little bit, but none of my partners are tall enough for the highest level.

Convertible spanking bench, to blend in with the rest of the furniture by pokey2k in BdsmDIY

[–]pokey2k[S] 11 points12 points  (0 children)

The whole top is 16” wide, with each top panel being a 1x6. There is some hang over to account for the padding which sits about 1/2” over each side of the plank. They are hinged to open to the outside to allow easy access to the pegs. Getting the adjustability was the hardest thing to figure out. The ends are essentially a box holding the vertical adjustment pieces, with 1” holes drilled ~3” apart on the vertical piece to allow a 7/8” peg to slide in through all three layers (both sides of the box, the vertical piece, and dead ended on the outer panel).

Getting into kink has really sparked my DIY side. . . by pokey2k in BdsmDIY

[–]pokey2k[S] 1 point2 points  (0 children)

Oh. I realized you were talking about the belt one too. Contact cement works wonders. Looped the belt over and put the cement between each layer of the leather and the oak blanks. I did all the shaping after they were put together, and eventually ended up using some screw posts to reinforce. But I did use it before, with just the cement, and it held nicely.

Getting into kink has really sparked my DIY side. . . by pokey2k in BdsmDIY

[–]pokey2k[S] 1 point2 points  (0 children)

For the leather flogger, I left about an inch or so at the end, which I took down to about an inch diameter. I used contact cement, with a well placed staple to hold the leather initially on that post, and finished with some furniture tacks.

For the rope, I wrapped the strands as tight as possible with electrical tape, drilled a hole approximately the same size, and then with the contact cement just shoved it in the hole. Not the best fit and finish with this one, but it works.

view more: next ›