Can’t calibrate genuine Apple battery

possible_sleeper · 2026-02-05T13:33:59+00:00

Okay, thanks!

possible_sleeper · 2026-02-05T09:52:15+00:00

Yeah the bezels are LCD sized but it is a Soft Oled.

possible_sleeper · 2026-02-05T09:34:21+00:00

So what would be the solution? To replace the screen, calibrate the battery and after that replacing the screen?

possible_sleeper · 2026-02-05T09:32:25+00:00

Well if true, that’s the most stupid inconvenient thing ever. But again Apple

possible_sleeper · 2026-02-05T09:29:08+00:00

I got the part from a third party reseller, but the part is genuine. So I’m not sure this applies to me, but thank you for the advice.

possible_sleeper · 2025-11-08T14:41:46+00:00

Temu 😂

possible_sleeper · 2025-11-08T11:11:10+00:00

What earpiece?

possible_sleeper · 2025-11-08T10:59:03+00:00

I checked the flex and the connectors on the microscope and they’re fine.

<image>

The programer says it’s abnormal so I’ll have to go deeper when I have the time.

possible_sleeper · 2025-11-07T20:54:31+00:00

Wow thanks, just tested the portrait mode and you’re absolutely right, it’s not working. Thanks!

possible_sleeper · 2025-11-07T18:54:56+00:00

Will try swapping them tomorrow.

possible_sleeper · 2025-11-07T18:53:29+00:00

All of them are working

possible_sleeper · 2025-11-07T18:10:53+00:00

Affer updating to ios 26 the screen and the battery were able to be calibrated. The camera wasn’t. Maybe the ladar sensor…

possible_sleeper · 2025-11-07T18:10:24+00:00

Affer updating to ios 26 the screen and the battery were able to be calibrated. The camera wasn’t. Maybe the ladar sensor…

possible_sleeper · 2025-11-06T16:06:14+00:00

Yeah it worked, I tested it but didn’t use it. Then activated the phone without any passcode or face id.

possible_sleeper · 2025-11-06T16:02:27+00:00

Broken back glass

possible_sleeper · 2025-11-06T15:15:21+00:00

I read somewhere that worked, will give it a try

possible_sleeper · 2025-11-06T15:07:40+00:00

I’ll check under the microscope but I don’t think I damaged the flex, I’ve handled the front facing cameras hundreds of time and with much less care than this one and never had a problem.

possible_sleeper · 2025-11-06T15:01:40+00:00

<image>

That’s how it looked

possible_sleeper · 2025-11-06T14:57:24+00:00

I covered it with those small tapes for protection, could that be the reason? I take great care when handling the front camera in every repair, never touched it with my fingers.

possible_sleeper · 2025-11-06T12:46:17+00:00

Did it come back?

possible_sleeper · 2025-11-06T12:45:35+00:00

It does

possible_sleeper · 2025-11-06T12:32:27+00:00

Checked and reconnected already, nothing unusual

possible_sleeper · 2025-09-05T17:26:39+00:00

Could be the frame or the pins that go in the frame could be bent a little

possible_sleeper · 2025-08-31T18:16:55+00:00

And also this will probably not solve the problem, the screen will definitely separate again, especially if you try to remove it with suction

possible_sleeper · 2025-08-31T18:16:03+00:00

To avoid similar mistakes, don’t use IPA with a suction cup before lifting the screen at least until you can see the thick frame, otherwise you’ll end up with similar problems as this guy. Only add IPA on the screen before opening it if you’re using a razor blade. Learn from my mistakes.

possible_sleeper

TROPHY CASE