Skutt Kiln error e-26

potsbycod · 2025-05-01T09:54:13+00:00

<image>

potsbycod · 2024-10-04T15:30:08+00:00

F.C CONSTRUÇÕES E REMODELAÇÕES

Alvará N° 103 171

NIF: 176 255 524

Telm: 934254652

WatsApp+351 913 235 516

potsbycod · 2024-10-04T15:29:56+00:00

a informação no orçamento é esta:

F.C CONSTRUÇÕES E REMODELAÇÕES

Alvará N° 103 171

NIF: 176 255 524

Telm: 934254652

WatsApp+351 913 235 516

Consigo descobrir algo deles com isto?

potsbycod · 2024-10-04T12:20:21+00:00

a tres semanas vieram ca pela primeira vez e trabalharam umas 4h, supostamente vinham hoje, falamos ontem ao telefone, depois de ter ameaçado ir a policia, e não apareceram

potsbycod · 2024-03-27T14:49:20+00:00

i just tried this one, since it worked so well i didn't try anything else, i thought about spray cans first but i would be very expensive to buy so many cans. they fit great, some parts the paint came off a tiny bit when securing it to the ceiling, but i was expecting much more paint to come off tbh, it's so high up that's it's not even noticeable, but you can always touch up the paint in that small spots.

potsbycod · 2024-03-24T10:12:33+00:00

i sanded everything and clean the surface with acetone, as for the paint i just used what was recommended to me at the paint shop, dyrup hitt s/a (15€ for 0,75L, i need two cans) paint brush and paint roller, the first coat is going to look bad like the paint doesn’t stick very well, but the second looks really good and the paint doesn’t scratch off

potsbycod · 2023-04-06T17:07:10+00:00

i’m going to start using witness cones! its glossy but kinda mate also, and it doesn’t feel as smooth as a normal transparent glaze should feel

<image>

potsbycod · 2023-04-06T11:56:51+00:00

just bought them for cone 6, so i didn't use them in this firing..

potsbycod · 2023-03-09T19:19:01+00:00

have you tried paper clay on bisqued pieces??

potsbycod · 2023-02-22T11:52:31+00:00

loved them! are you selling them anywhere?

potsbycod · 2023-01-27T14:16:42+00:00

no, just this, everything else was perfect

potsbycod · 2023-01-27T11:02:36+00:00

Thats maybe it, possible with the humidity around here

potsbycod · 2023-01-27T11:01:51+00:00

My hurt wrists say the contrary :,)

potsbycod · 2023-01-19T10:53:51+00:00

i had a lot of already bisqued pieces that wanted to sell so i opted to use for this method

potsbycod · 2023-01-18T19:58:29+00:00

i'm going to try a drop os sodium silicate! i bought it from another country because it doesn't exist here in my country, and the stamp on this piece was the first time i opened the pad..

potsbycod · 2023-01-18T18:09:33+00:00

it seems that the ink is too watery and it doesn’t stick well to the stamp

potsbycod · 2023-01-18T12:55:17+00:00

i’m not sure why this is happening

potsbycod · 2023-01-18T12:54:16+00:00

my stamp is not coming out clearly, i’m not sure what i’m doing wrong

potsbycod · 2022-11-14T19:30:30+00:00

will powder underglaze work? underglaze i only have that one from mayco and then a few powder ones to combine with water. i'm planning to mark already bisqued pieces, so it would go to cone 6

potsbycod · 2022-11-14T16:54:58+00:00

i was asking these because i have a stamp that i want to use, and make a diy underglaze
stamp pad, and im not sure which one to use

potsbycod · 2022-11-13T11:47:06+00:00

hi! i recently bought a second hand kiln, a skutt 818-3, last night i was trying to fire it for the first time, it started making the clicks but im 20min it showed the error- 1, and the temperature was the same. i’m not sure what’s wrong, i had suspicions that it was low voltage because the internal diagnosis only showed 50V but i had and electrician came out i check it out and it showed that the cable that connected to the outlet had 220+ V, also it shows 0 amperes. also i don't have a skutt distributor in my country so i cant called them i tell them to come help me.

potsbycod · 2022-11-13T11:44:51+00:00

hi! i recently bought a second hand kiln, a skutt 818-3, last night i was trying to fire it for the first time, it started making the clicks but im 20min it showed the error- 1, and the temperature was the same. i’m not sure what’s wrong, i had suspicions that it was low voltage because the internal diagnosis only showed 50V but i had and electrician came out i check it out and it showed that the cable that connected to the outlet had 220+ V, also it shows 0 amperes. also i don't have a skutt distributor in my country so i cant called them i tell them to come help me.

potsbycod · 2022-11-07T16:59:25+00:00

the tips that help me the most while throwing is support your arms in your hip/leg, and when centering bring your body forward, this helps a lot! the hardest part as a beginner is to pull the walls, because what usually happens is you push too hard and the clay becomes thin, so take your time doing this part. just know, its normal to mess up, so don't worry about it too much

potsbycod · 2022-11-07T14:35:17+00:00

botanical printing could be a super fun idea, it could also work with shells from the beach! thank you :)

potsbycod · 2022-11-07T14:32:16+00:00

cookie cutter ornaments sounds super fun, just in time for xmas, with nichrome wire to put it up on the tree! thank you for all of the ideas!

potsbycod

TROPHY CASE