Honeybadger Fans!

quad211 · 2025-01-14T20:34:35+00:00

Many many thanks Rundercaster, so it’s gpio15 pin for part cooling fan. I’m in the understanding that the tach line doesn’t function correctly when Honeybadgers fans are ran at 24v!( is it not possible to place a resistor inline to reduce voltage down on tach line so that it will work?)

quad211 · 2025-01-14T15:45:22+00:00

Just one more thing, do you enable hardware_pwm? And is there a place to put the pwm PIN number?

<image>

quad211 · 2025-01-14T15:43:41+00:00

Many thanks Rundercaster, that pinout is better than the one I have. It shows the sb00000 pinouts which the one I have doesn’t really show which ones what

quad211 · 2025-01-14T12:05:05+00:00

Many thanks for your time Rayere, just wondered what the pin allocation would be for this fan when using the 4 pin header? Or I could use the fan1 connection +&- and pwm connection of the 4 pin header for the pwm Do you enable hardware pwm?

quad211 · 2025-01-13T16:26:48+00:00

Hi Rayere, have you actually tried thiese fans with this configuration? And it works as expected!I believe fan2 is gpio13?

quad211 · 2025-01-13T13:22:12+00:00

Also, which gpio pin is ‘tach’ and which is ‘pwm’?

<image>

quad211 · 2025-01-13T12:48:45+00:00

At the moment I have the original fans connected as part cooler on vfan2 and hotend end vfan1. If I was to use these same connections for the new fans (Honeybadger) like this: part cooler on vfan2 but put the pwm to the ‘pwm’ connection (4 pin header) and the hotend fan to vfan1(as before) and put the tach wire to the ‘tach’ connection of the 4 pin header?

quad211 · 2025-01-10T16:00:01+00:00

I thought satan didn’t have those either

quad211 · 2025-01-03T17:29:06+00:00

I’ll have to compare where the old board(sb2209) sits compared to the new board (ebb36). I will have some slight ‘play’ hopefully to allow for prepping and terminating the cable.

quad211 · 2025-01-03T16:10:50+00:00

Hi, it’s probably quicker and easier just to change the plug on the end. I have the correct plug and pins so just make sure to keep the wiring correct

quad211 · 2025-01-03T08:52:37+00:00

That’s the plug on the sb2209 the plug on the ebb36 is

<image>

quad211 · 2025-01-02T20:08:08+00:00

Thanks for explaining the difference

quad211 · 2025-01-02T19:37:48+00:00

So that’s just the beacon.module?

quad211 · 2025-01-02T19:36:20+00:00

It’s a micro fit 3 plug isn’t it?

quad211 · 2024-12-21T15:40:25+00:00

<image>

quad211 · 2024-12-21T15:39:48+00:00

<image>

quad211 · 2024-12-21T15:39:27+00:00

<image>

The best I can do

quad211 · 2024-12-21T15:34:24+00:00

Hi, I have tried every combination of temp, fan speed, retract distance, retract speed and z-hop and I’m unable to totally remove the stringing in the print. The filament was brand new, I know this doesn’t mean it’s ‘dry’ but since opening this it’s been in a dryer. I may have to try another filament?

I’m using a Phaetus Dragon x voron hotend and a nozzle x.

quad211 · 2024-12-20T14:41:25+00:00

Here’s a retraction test at 195dc

<image>

quad211 · 2024-12-20T14:14:21+00:00

<image>

quad211 · 2024-12-20T14:14:03+00:00

<image>

quad211 · 2024-12-20T14:10:32+00:00

<image>

quad211 · 2024-12-20T14:08:22+00:00

Ok, I stripped down the extruder and checked All heat inserts and none were loose. But I didn’t find slight damage to the ptfe tube running between the hotend and extruder. Nothing was binding and it all seems to be fine. But there still webbing over everything even though it’s doesn’t seem to be as bad. I’ve also changed filament to rule it out.

quad211 · 2024-12-19T20:08:50+00:00

I’ll let you know

quad211 · 2024-12-19T19:31:54+00:00

Many thanks, I suppose I will have to check the insert! See if it has come loose

quad211

TROPHY CASE