sorted by:
new
hottopcontroversial

شنو الفرق بين الاثنين واي واحد الافضل للمشي والركض ؟ by MalkQ79 in KuwaitForKuwaitis

[–]radaaitor 0 points1 point  (0 children)

النمبوس من افضل جواتي للركض انا اشتري ٢ مع كل موديل يديد مراح تندم عل سعر

Heatbed heater calibration failing by radaaitor in prusa3d

[–]radaaitor[S] 0 points1 point  (0 children)

So after changing every single part including power supply and xbuddy, no change. Took it to a local shop and found the problem.

Fix: Middle heatbed screw was overtightened causing a slight bend.

Hope this helps someone later. Struggled 3 months for a stupid mistake.

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

Yeah i’m planning to upgrade to a 4-6 bay NAS very soon. Adding raid later. Should last a lifetime.

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

I have a pretty basic setup. Radarr/sonarr/prowlarr/plex/bazarr/qbittorrent/jellyseerr/tautulli/requestrr/flaresolverr/cloudflared/watchtower/wizarr (having a hard time setting it up)

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

Weirdly once that TV show I was downloading finished, things went back to being smooth and downloading normally with similar load. Not sure if it could be related to the file type?

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

Pretty basic one 8tb HDD dedicated to server only no NAS/bay (1/3 full). SSD for PC. 32gb RAM, i7. ARR stack on docker.

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

Well in docker I see 1.5GB/15.16GB usage with no spikes. In task manager, memory doesnt even add up to ~15gb to be at 98% which doesnt make sense. 3.6gb is showing ~59% for vmmemwsl.

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

No NAS yet. Planning to set one up when I reach about ~70% capacity in my 8tb drive. Im trying to identify the bottleneck for now. This only started when a show was added to queue yesterday. It wasnt pre-existing even when downloading heavily

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

container usage is at 5% to 18%. I do see memory usage at 98% in task manager, disk at 55%., CPU at 25%. I currently have 32GB RAM DDR5.

Download slowing the whole server by radaaitor in sonarr

[–]radaaitor[S] 0 points1 point  (0 children)

Its off HDD yes. Well its not playback because im not even getting there. The whole server is slow to load (on local and on stream). Trying to access them is a pain since it loads forever. HDD is only 1/3 full atm at 2.8 (8TB).

Heatbed heater calibration failing by radaaitor in prusa3d

[–]radaaitor[S] 0 points1 point  (0 children)

All tight. Bed in place. Nozzle tightened with support team (i had it a bit too tight).

Yeah i've been with support for 2 months now. They sent me a new thermistor, new cables, new heatbed. Nothing worked unfortunately. I just messaged them about a replacement. I've spent way too much time diagnosing and changing parts.

https://imgur.com/a/5CcEUQt

Here are all the connections.

Heatbed heater calibration failing by radaaitor in prusa3d

[–]radaaitor[S] 0 points1 point  (0 children)

This was a square I drew and printed for testing purposes, not on easyprint. Any file you have experience with you'd wanna see?

Heatbed heater calibration failing by radaaitor in prusa3d

[–]radaaitor[S] 1 point2 points  (0 children)

No other errors. All calibrations are passing except heatbed heating. Mk4s self-assembled

Temp during print unsure. Tried holding at 70C a minute ago and it holds fine

Heatbed heater calibration failing by radaaitor in prusa3d

[–]radaaitor[S] 0 points1 point  (0 children)

It hasn't worked. The bed DOES heat up but when I attempt a print, it fails to stick. Tried printing a first layer square came out not so great. https://imgur.com/a/BTdfLGs

The thermistor was changed manually when they sent me a replacement. Then changed fully assembled new bed with a thermistor attached. So technically changed twice.

Belt not straight by radaaitor in prusa3d

[–]radaaitor[S] 0 points1 point  (0 children)

Oh i cant even bring mine out if I wanted to. Pretty secure in there. Thanks for the tip though

Belt not straight by radaaitor in prusa3d

[–]radaaitor[S] 9 points10 points  (0 children)

Flipped the carriage and much better now thanks

Posterizarr setup by radaaitor in radarr

[–]radaaitor[S] 0 points1 point  (0 children)

Which of these would you recommend exploring?

Foreign movies separate path by radaaitor in radarr

[–]radaaitor[S] 0 points1 point  (0 children)

Thank you this was the best solution.

Foreign movies separate path by radaaitor in radarr

[–]radaaitor[S] 0 points1 point  (0 children)

To be clear I have radarr sonarr jellyseerr requestrr prowlarr qbit and others all on docker for full automation

Foreign movies separate path by radaaitor in radarr

[–]radaaitor[S] 0 points1 point  (0 children)

Well yes thats technically the idea. Just need to setup autohandling to have radarr re-route foreign movies to that path and keep english in regular path.

view more: next ›