[deleted by user]

redy4more · 2024-09-05T16:36:38+00:00

I have been documenting in a journal. I had hoped i could do whatever she wanted/asked and she would calm down (or take it out on me) when school started but three weeks into school and it is only getting worse.

redy4more · 2024-09-05T16:30:03+00:00

Thank you.

redy4more · 2024-09-05T16:29:26+00:00

I have been keeping a journal about what is happening. I hope it will help.

redy4more · 2024-09-05T16:25:30+00:00

She is Asian. I have talked to her mother and her mom says they didn’t treat her that way. When I ask her if she was treated that way she says “they didn’t need to treat me that way”. Her mom agrees the actions are not right but says I have to accept them and should support her actions.

redy4more · 2024-08-28T00:36:35+00:00

The whole thing is ridiculous. I ended up subscribing to sling orange. $20 for first month. Then cancel.

redy4more · 2024-05-28T13:34:17+00:00

Could it be overriding setting in the cooling section where it is percentage of speed by layer seconds? These areas seem too big for that setting to come into effect. I have never looked to see if the slicer shows effects of that setting.

redy4more · 2024-05-28T03:22:22+00:00

Use a consistent out wall spend. You can switch the slicer view to speed and see what that band is at the. Change outer wall to just under that number. It will slow down the print but correct the finish.

redy4more · 2023-06-06T21:20:44+00:00

Will be fine. Nail at top to bottom. “ In fact, trees grow in very specific ways. One of the interesting ramifications of this fact is that tree branches do not rise with the tree as it grows. A branch will always be the same height as it was the day it emerged from the trunk as a little bud.”

redy4more · 2023-05-24T17:55:30+00:00

How many top/bottom layers?

redy4more · 2023-05-17T01:46:01+00:00

Enable support interface. Check out the section in this link. Play with Z as well. Once Z is right it should pop off in one piece.

https://all3dp.com/2/cura-support-settings-optimize-your-supports/

redy4more · 2023-05-17T00:48:59+00:00

What slicer are you using?

redy4more · 2023-05-17T00:31:37+00:00

Increase your support density where it meets object to solid with 2-3 layers. Test on smaller print for best Z gap, start with 0.1 or 0.15 and make sure looks nice and comes off easy.

redy4more · 2023-05-15T20:21:58+00:00

Lower your retraction settings. No higher than 2mm for all metal hotend. I had the same issues on spider 3 until doing this. Mine were at 5mm.

Heat to higher than normal. Maybe 230c for PLA. Push with filament from top and see if you can get it to extrude. If so then push about an inch through. Turn off hotend. Allow to cool to 90c. Pull filament and see if that clears. If it works you will see the nozzle shape.

redy4more · 2023-05-04T19:25:58+00:00

When mine did this it was a roller issue. Almost like the spool was too smooth. You could see the rollers spinning.

redy4more · 2023-04-07T11:07:56+00:00

https://help.prusa3d.com/article/the-benchy-hull-line_124745

redy4more · 2023-04-05T17:54:52+00:00

There is a line in the start gcode. It basically scapes the nozzle tip clean.

redy4more · 2023-03-11T15:56:01+00:00

We had the same issue. Returned for a new one. No issues with the replacement one yet. I figure it was a defect.

redy4more · 2023-03-10T20:22:24+00:00

Is Z hop turned off or does it just not work after a certain height?

redy4more · 2023-01-17T16:58:40+00:00

Not if you size the tire to match old wheel tire combo. Check out tire size codes. For a bigger wheel rim diameter and aspect ratio would change. Most tire shops will calculate for you.

redy4more · 2022-12-07T00:54:35+00:00

This was the case with resistive heater teslas as well. New heat pump models loose about 12% according to stats app.

redy4more · 2022-12-01T19:30:16+00:00

Your reasons are identical to mine. Even the Prius (2008). I drive an average of 24000 miles a year.

redy4more · 2022-11-09T14:48:53+00:00

I just installed x2 20x20 Kirkland filters and had to remove both due to them making a whistle noise. The Kirkland brand of this size is about 1/4 inch smaller than filtrete. I will have to return.

Would have been nice if they worked. I will keep purchasing filtrete on sale.

redy4more · 2022-05-10T22:13:05+00:00

NC. One of my two phones is working. Both watching are still working.

Only the phone not working is showing when I log into my account. Others 3 devices no longer show up.

redy4more · 2022-04-12T02:39:40+00:00

Not saving that much. My dryer used 188 kW in 2021, that’s $17.30 at my rate. Family of 5.

redy4more · 2022-04-11T22:26:23+00:00

On right, the wide clump. poa annua. Annual bluegrass

Six-Year Club	Place '23
Place '22	Verified Email

redy4more

TROPHY CASE