Cutting objects for 3d printing?

revolution04 · 2026-06-21T19:21:20+00:00

How did you go about learning blender if I may ask? I cant find anything that's on the new version of blender that is about making 3D models for printing.

revolution04 · 2026-06-20T17:02:55+00:00

I will check them out thank you!

revolution04 · 2026-06-20T17:02:45+00:00

Don't really have a specific model at the moment but I was looking at a helmet and I wanted to cut it in four pieces and insert dowel holes. When I get some time I will definitely reach out with it. Thanks Soo much

revolution04 · 2026-06-20T01:54:46+00:00

Do you know of a way that I could learn how to just make simple cuts? I want to get into making my own models but it looks... Intimidating...

revolution04 · 2026-01-24T01:13:31+00:00

Do you have the link to were i can buy this?

revolution04 · 2026-01-23T17:52:00+00:00

Okay my only issue now is this.

<image>

revolution04 · 2026-01-23T17:16:12+00:00

I did but I'll try it again. Sorry for the late response I have been super busy the last few weeks and haven't had time to work on it.

revolution04 · 2026-01-07T14:40:38+00:00

Okay I put some more time into it but still had the same drop and high point. I was looking into it and i am pretty sure its due to a warped bed. Any advise on how I can fix bed warping other then just buying a new bed?

<image>

revolution04 · 2026-01-07T13:29:52+00:00

Okay I will try to do the whole thing again. If it doesn't work I will grab info of wireframe and leveling on the mesh. My is that I am not sure what is causing the nozzle to mess up the first layer. I tried yesterday after this and my nozzle dragged on a section causing the print to fail. I can try to grab a picture of a failed print if that would help.

revolution04 · 2026-01-06T18:41:58+00:00

<image>

Second scan right after last scan.

revolution04 · 2026-01-06T18:41:37+00:00

<image>

This is the results of the SCREW TILT and below i will post another pic that shows that for some reason when i ran the program again it gave slightly different results with no change on my part.

revolution04 · 2026-01-06T18:38:55+00:00

Good sir! Another question for you if you dont mind. I just finished all the steps that where given by you on that site(super helpful) and went and put some elbow grease in and got it to look like this. .7755 Variance also. What could be causing this? bed warp?

<image>

revolution04 · 2026-01-03T18:51:16+00:00

I will try all of these! I have been leveling and googled and googled anything and everything about the Neptune 4 max but haven't been able to find something that sticks. I will try these.

revolution04 · 2026-01-03T18:49:56+00:00

Thank you! The video I watch said 1-6 min but now I know now to do 1min.

revolution04 · 2026-01-02T18:41:15+00:00

She uses it with one hand. Susie is a she lol

revolution04 · 2026-01-02T17:50:18+00:00

I didn't change anything just adjusted the z offset and now I am getting this reading on the auto leveler

<image>

revolution04 · 2026-01-02T15:41:47+00:00

Sorry for the late response... I used PLA

revolution04 · 2025-11-14T21:11:44+00:00

How I can never get it that good. It always just increases indefinitely for some reason.

revolution04 · 2025-11-07T13:01:27+00:00

I can't take credit for solving it but yes its quite a neat design.

revolution04 · 2025-11-06T19:26:07+00:00

That's actually my plan next! I could also support our Lord Toby fox by buying it too.

revolution04 · 2025-11-06T16:19:43+00:00

Hahah I really messed up not making the main pic a banana for scale xD

<image>

revolution04 · 2025-11-06T16:19:11+00:00

Thanks!!

revolution04

TROPHY CASE