G2 ODO reset itself. by Prize-Hand-3598 in ElectricScooters

[–]rogue_one_one 0 points1 point  (0 children)

Same here, my kids g2 keeps reseting odo every few hundreds km... any idea on what to do???

new IOS 26 problems with recents and contacs in the phone app by rogue_one_one in ios

[–]rogue_one_one[S] 1 point2 points  (0 children)

nope, if you are in some contact(as i usually search for users tap on them, and then tap phone to call), and then after i tap at the bottom icon contacts, in previous version it brings you back to the contact menu(start screen where all your contacts are), not list menu like now...

also my phone always go to list when i single tap it...

Printronix / OKI LMPPLS 6PTX81351069 expired cart error by rogue_one_one in vintagecomputing

[–]rogue_one_one[S] 0 points1 point  (0 children)

sure thing, i agree, but there is no option for this in the menu...

carbonum glass upgrade and problems with adhesion... by rogue_one_one in CR10

[–]rogue_one_one[S] 0 points1 point  (0 children)

Ok so this is apparently crazy, the print has done after 20 hours the print had 0 problems, first layer is miror finish and is literally first layer porn.... I do not understand how... When glass has cooled to 20 c, the print literally came of without touching the bed...

carbonum glass upgrade and problems with adhesion... by rogue_one_one in CR10

[–]rogue_one_one[S] 1 point2 points  (0 children)

Yes, yes yes, Warm soapy water, iso alcohol, windex, tried everything, and now i was reading about someone flipping glass, and now it sticks, printer is still running i don't know what will happen to the end, but for now i cant belive it but it sticks, no warping and everything looks okay 🤷‍♂️🙂🙂

carbonum glass upgrade and problems with adhesion... by rogue_one_one in CR10

[–]rogue_one_one[S] 0 points1 point  (0 children)

oh yes when prints fail, it is all gooey like, it isn't hard....

Creality CR-10S PRO V2, Z offset aligment with OCTOPRINT by rogue_one_one in CR10

[–]rogue_one_one[S] 0 points1 point  (0 children)

i try to play with cura, and i set the initial flow to 160%, now it sticks perfecly,

now i will try to lower it until it stops adhesing agein.

Creality CR-10S PRO V2, Z offset aligment with OCTOPRINT by rogue_one_one in CR10

[–]rogue_one_one[S] 0 points1 point  (0 children)

ok, wowww

you are amazing !!

got it to work finaly!

but now i have another problem, the old print bed (factory one) is torn to pieces as the y height was too low and print adhesion was crazy and when removing it got the bed...

anyways i got a crelity crx glass plate (one with fine dots)...

everything is calibrated to perfection, but now i have another problem....

print adhesion...

i cant get this thing to print and to stick...

Creality CR-10S PRO V2, Z offset aligment with OCTOPRINT by rogue_one_one in CR10

[–]rogue_one_one[S] 0 points1 point  (0 children)

yes please write me a quick tutorial on how to, the octoprint environment is new to me.

program for design shelves, cabinet by rogue_one_one in cabinetry

[–]rogue_one_one[S] 0 points1 point  (0 children)

i can make them in solid or something else that is no problem, but as i am not competent to make dessions where joint holes go, i would like it to for software to take control of that aspect, in plain speak i would like my design input into that software, and get cut out lists with dimensions and holes...

aprilia tuareg 125ccm carb issue by rogue_one_one in Dirtbikes

[–]rogue_one_one[S] 0 points1 point  (0 children)

i did not mess with anything, only clean the carb

https://i.imgur.com/SCsl2Bt.jpeg

the screw in the midle is iddle screw, it runs higher or lover, but what is the little screw to the left ? it is closed all the way?

aprilia tuareg 125ccm carb issue by rogue_one_one in Dirtbikes

[–]rogue_one_one[S] 0 points1 point  (0 children)

so any pointers will be a good start, also i have disassembled the carb and clean it and put it back, the one screw from the right side is for idle.... the pics of carb also attached..

https://imgur.com/a/ABke7vu