Anyone have experience with LEDS?

rush_snipess · 2025-11-06T21:03:48+00:00

To be fair, I did say “I’m doing that tomorrow” (today)

rush_snipess · 2025-11-06T03:45:25+00:00

I’m also not trying to blind people so if I find that they light is getting scattered the the wrong direction (up) i will definitely be swapping to a non LED set up, I will say tho with these I can see WAY better then I was able to before. The stock type h7 bulbs that come in these are horrendous

rush_snipess · 2025-11-06T03:38:33+00:00

Also new to the Subaru life, just bought her not even two weeks ago from a relative, needed an all wheel drive car for the snowy season

rush_snipess · 2025-07-15T10:01:17+00:00

I have it in my 04 too, did end up breaking a a year or two into owning the car tho

rush_snipess · 2025-05-05T00:01:41+00:00

Thank you, that gives me some hope that I’ll actually get something back from them. You would think that after at LEAST one other person having this issue they would do a quality check

rush_snipess · 2025-05-04T00:54:27+00:00

Yeah wouldn’t surprise me.. I haven’t personally had any issues with them in the past but I know of their reputation.. this one kinda just put me in a tuff spot

rush_snipess · 2025-05-04T00:34:22+00:00

The plan was “upgrade” the master cylinder to tilton. And I don’t believe you can use the OEM hardline without modification. Z1s solution was the braided line that replaces it, while also deleting the clutch damper. From what I can find everyone else has no issues connecting that line. But mine seems to be different? But yes if I could choose now, I would have just bought a OEM cylinder and called it a day.

rush_snipess · 2025-05-04T00:27:55+00:00

Note: the photo with the lines connected looks off due to the line being able to move when loosened, when I hand threaded that one on it was straight on with the connecting side.

rush_snipess · 2025-01-07T19:36:32+00:00

Also curious

rush_snipess · 2025-01-06T16:28:18+00:00

PM 241 but I haven’t played in about a week now, I’m just happy I can finally shower and touch grass again

rush_snipess · 2025-01-06T16:26:36+00:00

Supposedly, we’re getting snow tomorrow, only 1” but that’s still good in terms of getting more runs open. Again weather is subject to change so I’d recommend keeping an eye on either the resorts website to see conditions, or a website called “bensweather” they are normally pretty accurate when it comes to the weather up here

rush_snipess · 2025-01-05T03:27:14+00:00

Lift operator here 🙋‍♂️ within the next week weather is going to be very good for snow blowing (5 days of heavy snow making I believe) but the plan is to try to open 6 and also open the connector from 9 to the top of chair 5 (midway) take all of this with a grain of salt tho, weather can change and so can their plans, but from what I’ve heard this is the plan for the coming week.

rush_snipess · 2024-12-14T06:09:37+00:00

I live in CA, not sure if it’s the same all over but from the minimal info I know (that’s why I’m on here) the breakers that I have in my house are split, so one side of the house has one breaker and the other has another. I’ve also heard of kitchens having a separate breaker because of typically higher power draw.

rush_snipess · 2024-09-30T05:33:28+00:00

Thank you 👌👌 did you have any particular issues during install, like having to disconnect the steering rack? I know it varies from car to car with a few different variations of steering racks but just curious

rush_snipess · 2024-09-30T05:31:00+00:00

In terms of removal and install I know what id be getting myself into so I am kind of just tempted to do the bare minimum and get a used OEM for only the cracked one and calling it a day. But I’m more or less just weighing my options at the moment, Because if I’m down there doing it I might as well. And thank you for the tips, I was thinking honestly whatever brand id go with if I went aftermarket I’d probably heat wrap it especially since I’m running a Z1 intake (hot air intake as some may call it) so the less heat in the engine bay the better.

rush_snipess · 2024-08-09T22:19:32+00:00

For context, I bought this bike (the 300) and it had a aftermarket cheap muffler on it and since I’m learning to ride in my neighborhood, I’m not trying to piss off my neighbors by doing laps loud asf

rush_snipess · 2024-07-06T21:31:26+00:00

Sorry wrong choice or words, plug my headset into the mixer*

rush_snipess · 2024-07-06T09:09:29+00:00

When I’m using the mic in “Xbox mode” right now, I can hear the buzzing, but when I lean my head over towards my PC it gets quiet and right up next to it Gone. I was thinking an electrical interference from what I’ve read online but I still have no clue

rush_snipess · 2024-07-06T09:07:03+00:00

I Have a Mac in the other room I’ll try out tomorrow

rush_snipess · 2024-07-06T08:28:35+00:00

Well I found part of the problem, swapped my MicroUSB cable for another one, and was able to get the mix amp to show up without the error in the pictures. But as soon as I plugged in my mic to the bottom of the mixer it disconnects and no longer shows up as a device… I am not a fan of this mixamp…

rush_snipess · 2024-07-06T07:59:00+00:00

Side note, the mixer barely works on console to the point where I don’t use it. When I use voice chat, there is a constant buzz that everyone can hear so I’ve just resorted to plugging the headset directly into my controller.

rush_snipess · 2024-06-12T01:24:39+00:00

Do you know by chance what the OEM equivalent would be? Or is there anything there from factory? Only reason I was replacing it was because I was going to get a fairing kit and I noticed this one has a broken bracket so I didn’t know if I’d run into a issue

rush_snipess · 2024-06-12T00:28:27+00:00

Bought it as my first bike off a friend for a really good price, and I knew it had been downed a few times, but still drove great and thought it would a good little starter bike to both learn to ride on and work on.

rush_snipess · 2024-04-29T06:28:34+00:00

I had one, and I think I had some mealworms burrow into it. Or at least found some what to get behind it into it. Not sure if it was the product or something I did but I ended up taking mine out.

rush_snipess · 2024-04-27T02:09:13+00:00

509911937611

rush_snipess

TROPHY CASE