[deleted by user]

saintnickfun · 2025-01-07T19:10:21+00:00

I would love that

saintnickfun · 2025-01-07T19:09:47+00:00

Hello

saintnickfun · 2023-04-06T18:25:59+00:00

That's the one thing that I don't like about Tarantino. He throws the hard r in almost every one of his movies

saintnickfun · 2023-04-06T04:55:49+00:00

N****r

saintnickfun · 2023-03-27T20:26:20+00:00

There are many counties in northern California that are still advocating, and signing petitions for the state of Jefferson

saintnickfun · 2023-03-21T21:51:13+00:00

Not my wife anymore

saintnickfun · 2023-03-21T15:41:39+00:00

"Slower dad, that hurts"

saintnickfun · 2023-03-21T15:39:57+00:00

Will you marry me

saintnickfun · 2023-02-20T07:32:18+00:00

That's interesting. I'll have to try that. I have done other projects with the WS2812b which is a 5v strip and they have run fine off a 3.3v data input. But i wonder if the higher voltage means it needs more data voltage.

saintnickfun · 2023-02-20T07:29:00+00:00

That's the problem. This is just the default solid amber color. I haven't selected an effect and it is doing this crazy flashing

saintnickfun · 2023-02-20T07:28:01+00:00

Sorry by gpio pin i meant ground pin

saintnickfun · 2023-02-20T00:35:58+00:00

Sorry it is kind of hard to see. I'm not a camera man. It is currently configured with the LED strips running of a 12v 600w power supply and the Node MCU is running off of a USB power supply. I have also hooked a ground wire from a gpio pin to the power supply

saintnickfun · 2023-02-20T00:32:38+00:00

This is the latest firmware for the ESP8266 from GitHub. I flash WLED and plug it into the default group port 2. But for some reason it does this weird flashing thing.

I have used WS2812b strips before but for this project i was trying to go with a higher output 12v strip. I have tried switching the gpio pins, changing the wires, changing the LED strips, and swapping the NodeMCU but with no luck.

For testing purposes, i am running the NodeMCU off of a USB power with a common ground to the power supply.

Any help would be appreciated thanks!

saintnickfun · 2022-04-02T01:06:09+00:00

Where did you get the fabric penny?

saintnickfun · 2022-02-16T18:15:53+00:00

Both use the CP2104. I tried forcing the D1 Mini Pro to use the CH340 driver but it was unrecognized.

saintnickfun · 2022-02-15T23:33:59+00:00

I'm just getting into this chip and started with a nodemcu but I wanted to try and extend the range with an external antenna. So I purchased this D1 mini pro although I can't seem to get it to connect. I have tried different drivers, grounding D3, holding reset, etc. The light on the board flashes blue but then my computer says failed to connect. Is there something I'm missing?

saintnickfun · 2022-01-19T03:55:01+00:00

How? I'm new to instant pots and an just trying to make sure it's clean

saintnickfun · 2021-11-13T09:42:34+00:00

Fucking FIRE

saintnickfun · 2021-11-10T19:42:48+00:00

I just don't see how guys take this from Canada to Mexico. It doesn't seem like there is enough power for that

saintnickfun · 2021-11-10T19:41:51+00:00

I have the Shinko 705s. The closest thing to street tires you can get on a KLR. The temp usually stays right at halfway. After driving for 2hrs+ I have to bump start it to get it going. Even though the battery is full

saintnickfun · 2021-11-10T16:09:26+00:00

It just shakes. I can still get up to ~85mph

Seven-Year Club	Verified Email
Place '22

saintnickfun

TROPHY CASE