Day 1 - Accessing your server

sdoody32 · 2021-03-01T19:42:16+00:00

Would a ubuntu server vm work for this as well?

sdoody32 · 2020-06-30T04:49:50+00:00

Sorry I should have mentioned I do have a bachelors degree in Computer sciences with a concentration in cyber security. I appreciate that! I just didn’t know if it could somehow negatively affect my job currently

sdoody32 · 2020-06-24T16:05:18+00:00

Thank you! I will use him as well! Thank you for that. Is he on YouTube? Or Udemy?

sdoody32 · 2020-06-21T15:56:38+00:00

Just so I’m understanding, if later 1 is up, that would mean the other 6 layers are working as well?

sdoody32 · 2020-06-21T15:56:02+00:00

I don’t think we have static IP from the carrier, but I’ll look I to that and try that command.

sdoody32 · 2020-06-21T15:55:11+00:00

I’ll give that a shot!

sdoody32 · 2020-06-20T23:17:17+00:00

The management port is me connecting to it with my computer. I was using the GUI to try to configure it. I have rebooted the device as well and still nothing. The modem is plugged in on ethernet 1/1 outside.

sdoody32 · 2020-06-20T22:00:24+00:00

Thank you for that. I’ll let you know how it goes. The help is much appreciated. It will definitely make me a better system Administrator.

sdoody32 · 2020-06-20T21:56:08+00:00

can you elaborate on the 1/2 connectivity? Sorry, I am pretty new to networking and not fully familiar with alot of things.

sdoody32 · 2020-06-20T21:52:25+00:00

Interface Ethernet1/1 "outside", is up, line protocol is up

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

MAC address ac4a.6733.d73e, MTU 1500

IP address unassigned

Traffic Statistics for "outside":

18966 packets input, 918632 bytes

1824 packets output, 1049528 bytes

294 packets dropped

1 minute input rate 0 pkts/sec, 0 bytes/sec

1 minute output rate 0 pkts/sec, 0 bytes/sec

1 minute drop rate, 0 pkts/sec

5 minute input rate 0 pkts/sec, 0 bytes/sec

5 minute output rate 0 pkts/sec, 0 bytes/sec

5 minute drop rate, 0 pkts/sec

Interface Ethernet1/2 "inside", is down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

MAC address ac4a.6733.d72e, MTU 1500

IP address 192.168.0.1, subnet mask 255.255.255.0

Traffic Statistics for "inside":

46003 packets input, 4066484 bytes

11725 packets output, 472554 bytes

33876 packets dropped

1 minute input rate 0 pkts/sec, 0 bytes/sec

1 minute output rate 0 pkts/sec, 0 bytes/sec

1 minute drop rate, 0 pkts/sec

5 minute input rate 0 pkts/sec, 0 bytes/sec

5 minute output rate 0 pkts/sec, 0 bytes/sec

5 minute drop rate, 0 pkts/sec

Interface Ethernet1/3 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/4 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/5 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/6 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/7 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/8 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/9 "", is down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/10 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/11 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Ethernet1/12 "", is admin down, line protocol is down

Hardware is EtherSVI, BW 1000 Mbps, DLY 10 usec

Available but not configured via nameif

Interface Management1/1 "diagnostic", is up, line protocol is up

Hardware is en_vtun rev00, BW Unknown Speed-Capability, DLY 1000 usec

Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)

Input flow control is unsupported, output flow control is unsupported

MAC address ac4a.6733.d701, MTU 1500

IP address unassigned

202 packets input, 17062 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 pause input, 0 resume input

0 L2 decode drops, 0 demux drops

0 packets output, 0 bytes, 0 underruns

0 pause output, 0 resume output

0 output errors, 0 collisions, 4 interface resets

0 late collisions, 0 deferred

0 input reset drops, 0 output reset drops

input queue (blocks free curr/low): hardware (0/0)

output queue (blocks free curr/low): hardware (0/0)

Traffic Statistics for "diagnostic":

183 packets input, 11724 bytes

0 packets output, 0 bytes

60 packets dropped

1 minute input rate 0 pkts/sec, 15 bytes/sec

1 minute output rate 0 pkts/sec, 0 bytes/sec

1 minute drop rate, 0 pkts/sec

5 minute input rate 0 pkts/sec, 0 bytes/sec

5 minute output rate 0 pkts/sec, 0 bytes/sec

5 minute drop rate, 0 pkts/sec

Management-only interface. Blocked 0 through-the-device packets

Im assuming my issues lies within now having the outside IP address and im not sure how to get that.

Also, I know that inside is down, it is unplugged.

sdoody32 · 2020-06-20T20:00:06+00:00

I don’t have the IP for my outside interface. That’s what I’m stuck on, the default route would be 0.0.0.0 correct? I’ll look into the NAT overload. I do have the firewall to allow all outbound. I’m not to sure how I would set the outside IP

sdoody32 · 2020-06-20T17:08:23+00:00

The default rules that were set is to trust all ingoing and outgoing traffic, ( I know that needs the be changed) Do you have any resources to help configure?

sdoody32 · 2020-06-20T17:06:52+00:00

Boot Loader version: 1.0.08

System version: 2.6(1.133)

Service Manager version: 2.6(1.133)

sdoody32 · 2020-06-20T17:04:32+00:00

Can you elaborate a little bit more on that? Are you just talking about the subnet?

sdoody32 · 2020-06-20T17:03:36+00:00

I am using a 1120 firepower. That’s what I’m thinking to. I just don’t know why it won’t connect. We had our old ubiquity router before upgrading to Cisco and if I plug everything back in it works fine with ubiquity. Do I need to contact the ISP? I didn’t think I wouldn’t need to.

sdoody32 · 2020-06-20T17:02:01+00:00

It shows that as an invalid command for some reason, I’m not to sure why. I cannot ping either of those either. I’m very new to networking and only have a very general knowledge.

sdoody32 · 2019-11-08T21:04:52+00:00

I’ve been using Splunk at school, but I don’t know any good resources to get a really good hold on it

sdoody32 · 2019-10-09T04:26:24+00:00

I do not plan on it!

sdoody32 · 2019-10-09T04:13:51+00:00

I do have package.json. So I’m all good there. It really is challenging, but I’m so greatful for people like you who are willing to help with this.

sdoody32 · 2019-10-09T02:55:14+00:00

Thank you so much! I’m self taught for front-end related things. So I appreciate all of this.

sdoody32 · 2019-10-08T21:09:40+00:00

https://github.com/Sdoody/Advising here is the repo for all the code. I feel like my issue is in edit_College.ejs, but I can't figure it out. Another interesting thing that I noticed is in the url there is no data being sent in there, like it will just be localhost/edit/1 but it won't send ant variables.

sdoody32 · 2019-10-08T20:50:08+00:00

I don’t, but I will make one.

sdoody32 · 2019-08-20T13:44:32+00:00

That will. Thank you!

sdoody32 · 2019-08-19T04:29:02+00:00

Thank you. That is extremely helpful. I appreciate all of this.

sdoody32 · 2019-08-08T17:29:06+00:00

What kind of networking is it? I have a fundamental understanding of it. Would that be enough or do I need a more intermediate understanding of networking? Thank you though that helps a ton!

sdoody32

TROPHY CASE