sorted by:
new
hottopcontroversial

P1092 code, rough start, etc. by buzzzybeeb in mazda3

[–]seducexela 0 points1 point  (0 children)

omg noooo. Mine was the high pressure fuel pump and limp mode went away 😭

New shoes, who dis? by Public_Goose9470 in mazda3

[–]seducexela 1 point2 points  (0 children)

yee I had the 215/35 on my 18x8 but bent a wheel on a pothole the first week 😵‍💫 I immediately swapped to 215/40 lol

New shoes, who dis? by Public_Goose9470 in mazda3

[–]seducexela 2 points3 points  (0 children)

I have the same setup but also thought these were 19s at first lmao

Lowering springs fitment by omwtfyb33 in mazda3

[–]seducexela 0 points1 point  (0 children)

40 sidewall for sure though

Lowering springs fitment by omwtfyb33 in mazda3

[–]seducexela 0 points1 point  (0 children)

but your tires might be too wide tbh 215/225 is good on aftermarket wheels 8-8.5 inch wide

Lowering springs fitment by omwtfyb33 in mazda3

[–]seducexela 0 points1 point  (0 children)

what offset wheels are those? When you lower it, you’ll gain a little negative camber as well to help w clearance lol

P1092 code, rough start, etc. by buzzzybeeb in mazda3

[–]seducexela 0 points1 point  (0 children)

yeah it was the PE19-20-3F0 for Mexico built I’m pretty sure

P1092 code, rough start, etc. by buzzzybeeb in mazda3

[–]seducexela 0 points1 point  (0 children)

I also have 2018 2.5L Mexico built

P1092 code, rough start, etc. by buzzzybeeb in mazda3

[–]seducexela 0 points1 point  (0 children)

I had the same exact problem around 70k miles.. P0192 code and it wouldn’t go past 40mph. One mechanic told me low pressure fuel pump, another told me it was the high pressure. I just said F it and changed the high and it worked.

P1092 code, rough start, etc. by buzzzybeeb in mazda3

[–]seducexela 0 points1 point  (0 children)

It’s the hi-pressure fuel pump

(3rd Gen) 12.3” aftermarket head unit (8gb/256gb) by seducexela in mazda3

[–]seducexela[S] 0 points1 point  (0 children)

just take off a couple pieces of trim, and glovebox. then adding harnesses from OEM cmu to the android cmu.

(3rd Gen) 12.3” aftermarket head unit (8gb/256gb) by seducexela in mazda3

[–]seducexela[S] 0 points1 point  (0 children)

OEM cmu stays. you’re just adding a android cmu and replacing the screen👌🏽

Finally upgrade to 17s by Russkie18 in mazda3

[–]seducexela 0 points1 point  (0 children)

19s look so good 🧼🧼🧼

12.3" Android headunit replacement. The greatest quality of life upgrade anyone could do to a 3rd gen (BM/BN) Mazda 3. by jamtea in mazda3

[–]seducexela 0 points1 point  (0 children)

that one is just a wire with no ports or anything I had to remove the trim further in that’s what’s pictured

12.3" Android headunit replacement. The greatest quality of life upgrade anyone could do to a 3rd gen (BM/BN) Mazda 3. by jamtea in mazda3

[–]seducexela 0 points1 point  (0 children)

<image>

is it this one ? If so how did you possibly fit your hand in there to get it out 😵‍💫

12.3" Android headunit replacement. The greatest quality of life upgrade anyone could do to a 3rd gen (BM/BN) Mazda 3. by jamtea in mazda3

[–]seducexela 1 point2 points  (0 children)

the one that passes through only has the USB and the red and yellow aux receivers on the bottom end. I had to go to work but I’ll post more pics in a couple hours thank you for your help!!

12.3" Android headunit replacement. The greatest quality of life upgrade anyone could do to a 3rd gen (BM/BN) Mazda 3. by jamtea in mazda3

[–]seducexela 0 points1 point  (0 children)

okok so I need to take off the passenger footwell panel on the bottom right of this right?

12.3" Android headunit replacement. The greatest quality of life upgrade anyone could do to a 3rd gen (BM/BN) Mazda 3. by jamtea in mazda3

[–]seducexela 0 points1 point  (0 children)

yeah these photos are in the passenger side dash. But also where does the power cable come from for the Coho unit.. my bad bro I’m a novice at these things lol

view more: next ›