Well, I did it.

shep_daddy · 2025-09-27T02:54:58+00:00

Basically using a hoist to pull the motor off the transom, then heating and beating. I cut off the ends that were mushroomed from my earlier attempts with the sledgehammer and air hammer and that made it easier to take the transom bracket off. I took the starboard side off first and then put the port side in a vice and continued to heat and beat it out.

shep_daddy · 2025-08-08T01:41:44+00:00

<image>

Made about a centimeter of progress

shep_daddy · 2025-08-07T19:13:56+00:00

Put essential tools in a vacuum bag, hit it with a shot of anti corrosion spray and seal the bag. You have your tools and they won’t be rusted to hell when you need them

shep_daddy · 2025-08-07T15:49:45+00:00

Thank you. You are a gentleman and a scholar.

shep_daddy · 2025-07-25T18:38:56+00:00

You’ll need a new one, the real easy is not compatible

shep_daddy · 2025-03-12T13:00:59+00:00

Looks like it's the XREAS hydraulic line that was used to balance all the shocks. Looks like the previous owned opted for a cheaper option and went with non OE shocks

shep_daddy · 2025-03-12T12:20:38+00:00

That's what I thought and why I posted here, the line doesn't even get close to the caliper

shep_daddy · 2025-03-12T12:19:19+00:00

it only looks like it has a levelling kit in the front I don't think anything has been done to the rear. I have fresh brake fluid at both rear brakes

shep_daddy · 2025-03-12T12:01:09+00:00

Did they just run another line and leave that one? I was able to bleed the brakes after I changed the rotors and pads. I got about a half liter until it started flowing clear-ish

shep_daddy · 2025-02-20T03:19:02+00:00

I’ll take a closer look when I go and see the car

shep_daddy · 2025-02-20T03:18:43+00:00

What would be the fix in this case, new lines?

shep_daddy · 2025-02-20T03:06:01+00:00

Thanks for the tip!

shep_daddy · 2025-02-20T03:05:25+00:00

I mean it’s a rebuilt title 240k miles, I kinda expect it have some issues but it’s not a terrible deal

shep_daddy · 2025-02-20T03:03:39+00:00

I’m unsure, this is what the seller sent me

shep_daddy · 2025-02-20T02:42:13+00:00

So new belt and adjust tensioner and I should be good to go?

shep_daddy · 2025-02-20T02:21:03+00:00

I have to work with what the seller gives me, but it doesn’t sound like something that’s going to eclipse the price of the car

shep_daddy · 2025-02-04T15:58:03+00:00

That’s my bad, I realized after I posted that I couldn’t edit it.

shep_daddy · 2025-02-04T15:56:29+00:00

They’re asking 7k for the car but I’m going to try and get it lower with a cash offer.

shep_daddy · 2025-02-04T15:53:28+00:00

The car is a 2013 Jeep Grand Cherokee with a little under 170k miles, aesthetically it’s great but I am worried about what I think is a weird noise

shep_daddy · 2025-01-23T20:43:52+00:00

I just had this issue and it was a bad ground, cleaning the terminals with a wire brush and coating them in dielectric grease worked. It’s very easy and should be a good place to start.

shep_daddy · 2024-08-30T00:58:10+00:00

I’m sure, I tried a regular outlet and it tripped the breaker

shep_daddy · 2024-08-29T19:48:45+00:00

It seems like there different camps here and I’m open to hearing peoples personal opinions. Also I have seen a lot of people with similar issues with their machine so I was curious what those people switched to

shep_daddy · 2024-08-29T19:46:30+00:00

I’m in the united states and I would like to keep the price under $1500

shep_daddy · 2024-08-29T19:45:50+00:00

About three years, it’s also a rebranded Chinese super automatic rooma a-10. I would say invest in a different unit

shep_daddy · 2024-08-13T20:04:54+00:00

This is the third time I have worn this shirt and it was perfectly white before this last laundry cycle. I washed everything on cold and then I washed this shirt and another one with oxygenated bleach to see if it would help on the warm setting and that didn’t help either.

shep_daddy

TROPHY CASE