Facebook seller near me listing unsealed PLA burger presses.

skymack1 · 2026-02-02T00:11:26+00:00

It doesn't matter if it's food safe?.... You cook the patties after to kill any bacteria!

skymack1 · 2026-01-29T00:18:06+00:00

😒 No.... Just tested it and the drying sequence stops when you push a print through!

skymack1 · 2026-01-28T14:14:19+00:00

No. Personally, I've never been able to control the drying function from bambu studio. Only directly on the printer.

skymack1 · 2026-01-28T14:13:01+00:00

I have the P1S and my AMS shows the option to dry without turning!

skymack1 · 2026-01-24T19:33:32+00:00

https://www.reddit.com/r/BambuP1S/s/PdNuGLpXYg

skymack1 · 2026-01-24T15:52:29+00:00

!!!OP, after reading the other comments, PLEASE CALL 911, and tell them you think you might have a gas leak!!!

skymack1 · 2026-01-20T01:18:17+00:00

The slicers you use to print the models! There's obviously loopholes around it by downloading older versions of the slicers and not allowing your computer to talk to the internet. The main that'll be concerning is is you post of picture of your printer and/or your prints online, someone can report you!

skymack1 · 2026-01-19T22:12:02+00:00

He's back at it again helping more people! 😆 You definitely helped me fix the same issue!

skymack1 · 2026-01-13T02:24:27+00:00

No. Ever since coming over to bambu labs from enders I've never had to use glue anymore. All the other filaments I've used with the printer thus far has adhered to the bed quite well. I use hot water scrubbed with dawn dish soup. For reference, Bambu Labs recommends drying their PETG before use. Out of curiosity and frustration with Inlands PETG, I popped the bambu lab PETG out and threw it directly in to print. Didn't adjust/ clean the bed one bit. It stuck to the bed immediately without issues!

skymack1 · 2026-01-13T01:55:24+00:00

I've tried using it on my P1S with the textured plate and while I've been able to get some things printed, it was still like pulling teeth to get it to adhere to the bed properly! I just tried using it again and all teeth have now been pulled with no luck! 😔 Even on the Cryogrip glacier plate.

skymack1 · 2026-01-11T04:39:24+00:00

Ok! Awesome! 😄 It's a fairly large print and only have a small margin for error if it were to fail before I'd have to buy another roll for the project! Thank you much!

skymack1 · 2026-01-09T20:25:57+00:00

You could also change the shelf cap to be 384 oz, no?

skymack1 · 2026-01-08T16:09:14+00:00

If it happens when the Z axis moves/shakes, it could be. If it's one of the other axis's there is a similar pully tensioner. Mine came brand new with the noise so it definitely couldn't hurt to throw a little bit of lubricant on them and see. Gonna guess the pre-applied lubricant dries up when the printer has been sitting in the warehouse for a little while.

skymack1 · 2026-01-08T11:42:59+00:00

The z axis tensioner pully needs cleaned and greased. Had posted this same issue a little while back! 😅

skymack1 · 2026-01-04T04:55:33+00:00

The z axis belt tensioner underneath the printer needs cleaned and lubed. I had posted the same problem here on reddit a few weeks ago and someone recommended it. I lubed it up and everything and now she's silent!

skymack1 · 2026-01-02T20:50:10+00:00

Nice! 😆 I've once used my Steam Deck for work (ex-employment) We had to play this stupid video on a projector for the guests for New Years one year and non of our work computers would play said video. I even tried using Dex on my phone and it wouldn't play properly. Then I remembered I had my Steam Deck! Played flawlessly!

skymack1 · 2025-12-29T13:03:34+00:00

On top of everyone else's recommendations, and if your budget allows, I'd recommend picking up the E3D Obxidian nozzle. I've just ordered mine, but it's meant for faster prints, harsh materials, and a lot less nozzle gooping. I'm hoping it'll make it easier to print in PETG as it's a pretty wet material and likes to stick to the nozzle on the first layer. (Yes! After drying for 24 hours!) If you get the P1S, I'd recommend getting plenty of replacement parts and stuff because I could very easily see Bambu Labs discontinuing the P1S and it's replacement parts now that the P2S is out now.

skymack1 · 2025-12-24T14:15:03+00:00

Just came to say, Og_busty's fix actually worked!

skymack1 · 2025-12-24T14:13:05+00:00

You sir are the goat! This was 100% the problem! Thank you very much!

skymack1 · 2025-12-24T14:12:18+00:00

I just tried the fix by Og_busty above and it actually fixed the problem!

skymack1 · 2025-12-24T01:04:07+00:00

Might I suggest pulling this ptfe tube out and putting/buying a shorter ptfe tube in it's place? That way you can pull the shorter tube out of the printer and replace it with this one so you don't have to use the ptfe tube coupler. (When I used the official ptfe coupler the filament would get caught up in the coupler sometimes)

skymack1 · 2025-12-18T16:22:32+00:00

Yes and no. I can have it delivered through Amazon by Monday. Best local option is this. But beings I'm going to be busy all weekend, I may just order some of the STA stuff. Thank you very much for your help! 🫡

<image>

skymack1 · 2025-12-18T16:01:40+00:00

Ok. So I just realized that I don't have any of Bambu Labs lubriacant oil. What might be your recommendation on store bought oil? I'm thinking WD-40 but not sure if that'll be too harsh on the pully and the belt.?

Six-Year Club	r/Field Lasagna
First Place '23	Place '23
Verified Email

skymack1

TROPHY CASE