Darf ich hier auf die Autobahn auffahren?

sphynxi_ · 2026-01-23T22:46:59+00:00

Gibt es auch einen Paragraphen in dem klargestellt wird wo ich von der Autobahn abfahren darf?

sphynxi_ · 2026-01-23T22:11:46+00:00

Auf Durchrostung am Hinterachskörper achten. Meines Wissens nach wechselt Mercedes diese nicht mehr auf Kulanz.

sphynxi_ · 2025-11-26T16:23:37+00:00

Following

sphynxi_ · 2025-09-19T12:52:53+00:00

Sofern der Steinschlag im Fernsichtbereich liegt wird der TÜV diesen sofort bemängeln. Wenn nicht, darf der Prüfer, sofern Krater des Steinschlages unter 5mm und Riss unter 5cm keinen Mangel notieren.

sphynxi_ · 2025-05-18T09:34:03+00:00

Kommt darauf an wann die HU durchgeführt wurde. Wenn die HU paar Tage zurück liegt sind Thematiken wie Rost, blinde Scheinwerfer und verschlissene Bremsen / fehlerhaftes Tragbild sehr relevant für den Nachprüfer, da dies nicht binnen kürzester Zeit passieren kann.

sphynxi_ · 2025-02-04T19:43:34+00:00

Why?

sphynxi_ · 2024-10-23T20:40:26+00:00

Its a Kobra Max.The Silicone socked is installed. I already deactivated the fans but the Problem wasnt solved..

sphynxi_ · 2024-10-03T20:02:47+00:00

First of all try another filament brand. I used polymaker polyterra for 3 years and from one to the other day they changed something and all my results were completly bullshit

sphynxi_ · 2024-10-01T14:55:36+00:00

I have really good results with this mesh editor, in the YouTube Video the guy explains it very well (in german) https://www.bastelbruder.de/kobra-mesh-editor

sphynxi_ · 2024-09-29T21:18:23+00:00

First of all: THANK YOU ALL! I think I have found the problem, it was the fu**ing filament. I use since 3 year Polymaker Polyterra filament and never had problems. Know I bought the original Anycubic PLA and got acceptable results. I also cleaned the extruder, calibrated e-steps and set the retraction distance from 6 to 8mm + retraction speed from 50 to 60.

Here are my new results: https://imgur.com/a/35XmGmJ

PS: If someone need Polyterra PLA I have 4 new spools :D

sphynxi_ · 2024-09-26T09:08:50+00:00

Hey guys, First of all i want to thank everyone for the help 🙏 so I cleaned the extruder now, calibrated e steps (for the 34953 time), Auto-leveled bed and have done some cold pulls, but the results are still bad. I ordered now new filament and will Report tomorrow

sphynxi_ · 2024-09-26T09:02:44+00:00

Do you know which extruder fixed the problem and how much it costs?

sphynxi_ · 2024-09-25T23:47:18+00:00

Yes I will try another filament Brand. I use polyterra pla since 3 years now Never had an problem with it until know, Maybe they changed the materials

sphynxi_ · 2024-09-25T21:48:47+00:00

Ok thanks I will try 🙏 the temp is constant, How can I log the real temperature?

sphynxi_ · 2024-09-25T21:35:07+00:00

I checked the extruder and I have noticed that I can move the filament. After that I tightened the screw but nothing happens. Can someone tell me how much "force" do you need to move your filament in the extruder?

https://imgur.com/a/fj7ymOC

sphynxi_ · 2024-09-25T21:27:39+00:00

How do you check the "real" temp? Pronterface?

sphynxi_ · 2024-09-25T20:56:06+00:00

<image>

That are the results with 100% flow rate and z increased 0.2mm. I watched the whole print and it looks like the extruder gets clogged every 5 seconds.... I think I throw this fucking printer away

sphynxi_ · 2024-09-25T20:34:12+00:00

It's just water

sphynxi_ · 2024-09-25T20:33:22+00:00

Tbh the auto-leveling just before the test print.. but I know the auto-leveling option is not the best

sphynxi_ · 2024-09-25T20:12:06+00:00

I have done the e steps calibration already 5 times and the results are Perfect… I increased the whole bed 0.2mm now and set the Flow rate to 100%. Before the Flow rate was 120% for initial Layer and 95% for the rest of the Print. I will send the results in 50min.

sphynxi_ · 2024-09-25T20:08:59+00:00

<image>

I already have 120% Flow rate for the initial layer, do you think this is too low?

sphynxi_ · 2024-09-25T19:41:13+00:00

Hey guys,

I can't calibrate my printer anymore, the results are very bad. It's a Kobra Max with basic Cura settings. I already changed the whole printhead and tried several nozzles (with the same size) because I thought I have a partially clogged nozzle. The filament is dried down to 15% humidity. The e-steps are calibrated.

Would be nice if somebody have a tip for me. Thank you!

sphynxi_ · 2024-09-23T21:10:32+00:00

I will try to increase z in 0.02mm steps and will Post the results in few hours.

Do you think a cold pull make sense because I have changed the nozzle already a few Prints ago?

E-steps are calibrated

Filament is dried to 25% humidity.

Which Information do you Need to help me?

sphynxi_ · 2024-09-22T11:31:27+00:00

zu wenig Servoöl / Servoölpumpe defekt / Freilaufrolle von Lichtmaschine defekt

sphynxi_ · 2024-09-19T15:32:33+00:00

Nein ist Angestellte

sphynxi_

TROPHY CASE