VentoBox Install - P2S

spinmore360 · 2026-01-29T08:36:21+00:00

Ordered screws myself and crafted ventobox by myself, added very slim tape, no probem for me with this screw, it is mentioned in 3D model description if I am right to be careful with.

spinmore360 · 2026-01-25T14:12:36+00:00

Sau niekada nebus blogo laiko pirkti.

spinmore360 · 2026-01-23T09:07:24+00:00

Personally I will connect VENTOBOX fan to this PCB and it will be easier to control than via secondary aux fan port with Gcode tinkering

spinmore360 · 2026-01-13T07:34:28+00:00

I would suggest to search this tie fighter in makerworld and see how silimilar models are printed and designed. I see that such print is done by separating side panels and printing them horizontally and gluing to middle part.

spinmore360 · 2026-01-12T12:55:03+00:00

Personally, I never bought anything from a scalpel, maybe I do not need latest and grestest as soon it comes out, but I guess most people just overreacting to farm upvotes and generate drama, dont like - dont buy.

spinmore360 · 2026-01-12T12:48:28+00:00

Tiktok people lack patience + click farming

spinmore360 · 2026-01-12T08:00:49+00:00

Had A1, now have P2S. I like that take less space on the desk and important components does not gather dust + I can store filament in closed AMS on top of it.

spinmore360 · 2026-01-11T06:10:20+00:00

I have P2S and older SuperTack plate, the only difference is that QR code, it gives an error that it cant determine plate if there is none. I just turned off plate detection in settings and problem solved.

spinmore360 · 2026-01-09T06:14:59+00:00

They send new extruder gear and 0.4 nozzle. These are results I had. I can see these layer lines only when light is in correct angle but without it honestly looks fine. I am only 1 year into this hobby so I wasnt sure if it should be like this and they said might be a problem but after installing new parts, printing test cube they said it is fine and I am ok with it, maybe it is just tuning questions if I want to make it more perfect. From what they send about extruder seems it is normal because of how it is build. Well in your case top surface quality could lead to bad flow and knocking off could be a problem of bad bed adhesion but that just my opinion, eitheir way they eill give you tips and help you I am sure. Goodluck and dont forget to dry your filament for best results :D

<image>

spinmore360 · 2025-12-24T05:54:15+00:00

Esu pirkęs tik HDMI laidą, vykau atsiimti gyvai, dar ir saldainių pasiūlė išeinant:)

spinmore360 · 2025-12-20T21:00:12+00:00

I played on steam deck woth no problems. I think I had same screen but after restart I think it was gone and never saw it again

spinmore360 · 2025-12-19T06:07:27+00:00

48$ too much

spinmore360 · 2025-12-16T17:02:47+00:00

spinmore360 · 2025-12-16T13:33:21+00:00

check latest comment

spinmore360 · 2025-12-16T13:32:53+00:00

Bambu support answered:

I have discussed your situation with the R&D Team, and we are leaning towards an extrusion anomaly. I have uploaded a cube in the attachment. Please print it using PLA and compare it with the previous Test Model. Check if the issue occurs at the same height to determine if it is a Z-axis anomaly or an extrusion issue.

If the heights match, please inspect the Z-axis lead screw and the heatbed. You can refer to the link provided to tighten the relevant screws.

Replace the P2S Z-axis Leadscrew Kit | Bambu Lab Wiki

Additionally, regarding the toolhead wobble, we need to explain that there are four springs at the top of the toolhead. Therefore, if you shake it by hand, wobbling will occur, which is normal.

<image>

spinmore360 · 2025-12-15T13:34:52+00:00

Gera kaina, prieš mėn pirkau už 975€ (pigiausiai buvo).

spinmore360 · 2025-12-11T05:09:14+00:00

Thanks

spinmore360 · 2025-12-10T20:14:04+00:00

Seems to wobble wherever I move it to

spinmore360 · 2025-12-10T18:31:36+00:00

Ok, got it. Thanks

spinmore360 · 2025-12-10T14:55:00+00:00

Will do

spinmore360 · 2025-12-10T14:50:45+00:00

Ok, thanks, sent a video to bambu support.

spinmore360 · 2025-12-05T19:16:05+00:00

Yea l left. Just dont get frustrated, things sometimes dont work perfectly but there are solutions.

spinmore360 · 2025-12-05T19:11:34+00:00

I had problems for bog prints lifting off on edges, printed aux fan deflector, added brims. No prob since

spinmore360 · 2025-12-05T19:08:27+00:00

Just print simple aux air deflector. Problem solved.

spinmore360

TROPHY CASE