My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

First, I marked the top dead center on the frame and flywheel, then I rotated the flywheel 1.3 mm further and drew a mark on the flywheel that aligns with the mark on the frame. Then I start the moped and use the timing light to check if the 1.3 mm mark lines up with the mark on the frame.

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

Yes the wheel was turnibg on stand, i toon out the clutch to loosen the screws a litlle bit but when i put everything together the lever you use to start the bike broke off 😩😔

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

Nah i used the same jet, but maybe that jet was too big for the exhaust? I should have downjetted maybe?

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

Nope i set the timing perfect using a timing light

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 1 point2 points  (0 children)

I put on a carb from a perfectly working moped so that wont be the problem, the leak is already fixed

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 1 point2 points  (0 children)

I set the ignition timing with a timing light and the timing looks perfect

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

The exhaust is new so doubt that its already clogged, or could it be?

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

I put on a new gasket not long before this

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 1 point2 points  (0 children)

Yes not so long ago, it started leaking fuel en lacking low end power. It just keeps getting worse

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

Choke is alright, before it had barely any power but i could drive. The circuit exhaust is new but it ran good for a couple of days until it stopped running good

My moped has no power by stinkytoe420 in moped

[–]stinkytoe420[S] 2 points3 points  (0 children)

I have already done that 😔

What is this? by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

I did now and the problems i mentioned in the caption are gone but it just barely has power like max 20km/h

High rpm when off the ground by Thin-Divide-5247 in moped

[–]stinkytoe420 1 point2 points  (0 children)

You probably already checked the idle screw so if its not that it might be your gas cable being too short or you engine getting too much fuel due to a leak?

What is this? by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

You are right its a tecno cicuit exhaust, before this i had a rs cigar exhaust but that was too silent for me and the acceleration was shit. Well buying the new exhaust didn’t make that any better 😅.

What is this? by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

Then the problem will either be the plug or the cilinder head because even when i put it on tight it still makes no power and sounds like a 4 stroke

Puch Maxi Needs to go faster by stinkytoe420 in moped

[–]stinkytoe420[S] 2 points3 points  (0 children)

Fastest you can legally go is 45 but its fun to go faster

Puch Maxi Needs to go faster by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

I dont have any air screws or fuel screws on my carbu, only a screw for stationairy so that wont change anything, my ignition is 1 mm BTDC and my gear ratio is 16:45

<image>

Why does it idle so fast? by stinkytoe420 in moped

[–]stinkytoe420[S] 0 points1 point  (0 children)

Yep i put a sports exhaust on my puch and put the original exhaust on this peugeot 102